ad2usb plugin discussion

Posted on
Sat May 12, 2018 7:04 am
maslett offline
Posts: 98
Joined: Aug 09, 2014

Re: ad2usb plugin discussion

Berkinet, apologies for the confusing response. I have made some progress. I got the installer code and added the keypad. The messages are now showing up in NC but the plugin is not showing the messages rather just error codes as shown below. Thanks for the assistance, Mark
Attachments
Screen Shot 2018-05-12 at 9.11.06 AM.png
Screen Shot 2018-05-12 at 9.11.06 AM.png (494.88 KiB) Viewed 738 times
Screen Shot 2018-05-12 at 8.50.59 AM 2.png
Screen Shot 2018-05-12 at 8.50.59 AM 2.png (479.83 KiB) Viewed 740 times

Posted on
Sat May 12, 2018 7:50 am
berkinet offline
User avatar
Posts: 3096
Joined: Nov 18, 2008
Location: Berkeley, CA, USA & Mougins, France

Re: ad2usb plugin discussion

maslett wrote:
Berkinet, apologies for the confusing response. I have made some progress. I got the installer code and added the keypad. The messages are now showing up in NC but the plugin is not showing the messages rather just error codes as shown below. ... Mark
Delete your keypad device, then recreate it and then restart the plugin. If that does not resolve the problem, you may also need to delete and recreate the zone devices.

Posted on
Sat May 12, 2018 8:00 am
berkinet offline
User avatar
Posts: 3096
Joined: Nov 18, 2008
Location: Berkeley, CA, USA & Mougins, France

Re: ad2usb plugin discussion

wikner wrote:
...and a whole bunch of these:
Code: Select all
   AD2USB Alarm Interface Error    Error on line 795
   AD2USB Alarm Interface Error    panelMsgRead: Error: log() takes exactly 5 arguments (4 given)
using 1.6.1

Sorry. Trying to code without being able to test can cause problems... try this:
https://drive.google.com/open?id=15K48L ... fo99bb9Mw6

Posted on
Sat May 12, 2018 9:15 am
maslett offline
Posts: 98
Joined: Aug 09, 2014

Re: ad2usb plugin discussion

Berkinet, thanks. I deleted the keypad and all zones. I created a new keypad which now shows clear and faulted. However it appears the plugin works for a little while and then crashes as it reads messages as various newly created zones are triggered. See attached. Thanks, Mark
Attachments
Screen Shot 2018-05-12 at 11.26.13 AM.png
Screen Shot 2018-05-12 at 11.26.13 AM.png (495.88 KiB) Viewed 723 times
Screen Shot 2018-05-12 at 11.12.58 AM.png
Screen Shot 2018-05-12 at 11.12.58 AM.png (496.14 KiB) Viewed 725 times
Screen Shot 2018-05-12 at 11.02.00 AM.png
Screen Shot 2018-05-12 at 11.02.00 AM.png (487.53 KiB) Viewed 725 times

Posted on
Sat May 12, 2018 9:55 am
berkinet offline
User avatar
Posts: 3096
Joined: Nov 18, 2008
Location: Berkeley, CA, USA & Mougins, France

Re: ad2usb plugin discussion

maslett wrote:
Berkinet, thanks. I deleted the keypad and all zones. I created a new keypad which now shows clear and faulted. However it appears the plugin works for a little while and then crashes as it reads messages as various newly created zones are triggered. See attached. Thanks, Mark
Did you restart the plugin after creating the new zones?

You can also try the version I posted earlier today to this threads. It will not fix the problem. But, may give better error messages.

Posted on
Sat May 12, 2018 1:42 pm
maslett offline
Posts: 98
Joined: Aug 09, 2014

Re: ad2usb plugin discussion

Berkinet, I installed the new version and things appear to be working. thank you for all your help. Mark

Posted on
Sat May 12, 2018 2:10 pm
berkinet offline
User avatar
Posts: 3096
Joined: Nov 18, 2008
Location: Berkeley, CA, USA & Mougins, France

Re: ad2usb plugin discussion

maslett wrote:
Berkinet, I installed the new version and things appear to be working. thank you for all your help. Mark

Thanks for letting me know. Did you get any series of log messages starting with " Zone Event test:...? If so, could you post a few here

Posted on
Sat May 12, 2018 3:46 pm
maslett offline
Posts: 98
Joined: Aug 09, 2014

Re: ad2usb plugin discussion

Once I stopped getting the error messages I downgraded to 1,6 and the error messages stopped. A little weird. Maybe there was something weird on my end with the install once the keypad programming issue was resolved. I will reinstall 1.6.2 and post a few logs. Although I don't think I have any error messages right now. Thanks once again.

Posted on
Sat May 12, 2018 3:54 pm
maslett offline
Posts: 98
Joined: Aug 09, 2014

Re: ad2usb plugin discussion

I reinstalled 1.6.2 seems to be working fine. There are no further extended error messages. Screen shot attached. I'll leave as is and will post any logs with extended error reporting if the occur. Thanks, Mark
Attachments
Screen Shot 2018-05-12 at 5.49.22 PM.png
Screen Shot 2018-05-12 at 5.49.22 PM.png (498.22 KiB) Viewed 639 times

Posted on
Sun May 20, 2018 6:01 pm
maslett offline
Posts: 98
Joined: Aug 09, 2014

Faulted zone's not clearing

Berkinet,

I noticed an anomaly with 1.6.2.

If I have a zone that is purposely faulted, for example I leave the kitchen window open for ventilation, then when a motion detector triggers it does not clear. If there isn't a faulted zone, ie the kitchen window is closed, then the motion detectors fault then clear normally.

Unfortunately there are no errors messages.

Thanks, Mark

Posted on
Wed May 23, 2018 11:46 am
berkinet offline
User avatar
Posts: 3096
Joined: Nov 18, 2008
Location: Berkeley, CA, USA & Mougins, France

Re: Faulted zone's not clearing

maslett wrote:
...I noticed an anomaly with 1.6.2.
If I have a zone that is purposely faulted, for example I leave the kitchen window open for ventilation, then when a motion detector triggers it does not clear. If there isn't a faulted zone, ie the kitchen window is closed, then the motion detectors fault then clear normally.

V 1.6.2 was for trying to debug the problems reported by @wikner (who seems to have disappeared). It was not intended for general use. Try going back to v1.6.1.

Posted on
Wed May 23, 2018 12:41 pm
maslett offline
Posts: 98
Joined: Aug 09, 2014

Re: ad2usb plugin discussion

berkinet wrote:
maslett wrote:
...I noticed an anomaly with 1.6.2.
If I have a zone that is purposely faulted, for example I leave the kitchen window open for ventilation, then when a motion detector triggers it does not clear. If there isn't a faulted zone, ie the kitchen window is closed, then the motion detectors fault then clear normally.

V 1.6.2 was for trying to debug the problems reported by @wikner (who seems to have disappeared). It was not intended for general use. Try going back to v1.6.1.
Ok I will try doing when I return. Thanks.


Sent from my iPhone using Tapatalk

Posted on
Wed May 23, 2018 3:28 pm
wikner offline
Posts: 172
Joined: Nov 02, 2003

V 1.6.2

V 1.6.2 was for trying to debug the problems reported by @wikner (who seems to have disappeared). It was not intended for general use. Try going back to v1.6.1.
I haven't disappeared, just busy. I am running 1.6.2. Do you want me to send you another high-debug-level log?

Posted on
Thu May 24, 2018 1:35 am
berkinet offline
User avatar
Posts: 3096
Joined: Nov 18, 2008
Location: Berkeley, CA, USA & Mougins, France

Re: V 1.6.2

wikner wrote:
...I am running 1.6.2. Do you want me to send you another high-debug-level log?
Are there any log messages containing "Zone Event test "? If so, please copy a few and post them here.

Posted on
Thu May 24, 2018 10:35 am
wikner offline
Posts: 172
Joined: Nov 02, 2003

Re: ad2usb plugin discussion

berkinet wrote:
Re: V 1.6.2

There were 5957 such messages yesterday. Here are a few.
Attachments
Zone Events Test.txt
(13.38 KiB) Downloaded 13 times

Who is online

Users browsing this forum: No registered users and 2 guests

cron