Fibaro Smart Implant - encrypted?

Posted on
Sun Jul 26, 2020 6:49 am
Umtauscher offline
User avatar
Posts: 542
Joined: Oct 03, 2014
Location: Cologne, Germany

Fibaro Smart Implant - encrypted?

Hi,
I just wanted to include a new fibaro smart implant with encryption, because I want to open my Entrance with it for security reasons.
At first, I got it included and synced, but it didn't perform as I expected. The Relais couldn't be switched by indigo resulting in an error message:
Z-Wave Error device "166 - Relay 1" does not support on command
which seemed to be odd.
So I removed the node and reincluded it without encryption and now I could switch the relays as expected. (now node 167) ?!?
Normally I would now give up and leave the device unencrypted but in this case I just wanted to get on the bottom of this.
So I removed the node and reincluded again. (now 168)
This worked, but noiw I could not sync. The errormessages in the userinterface were erratic, So I tried to reinclude agin, but got the errormessge the node is already included.
After that the sync succeeded, but in fact I don't know if it's now running encrypted or not.

What do you make of that log?

Code: Select all
Z-Wave                             Started controller inclusion mode with encryption

26.07.2020 14:27:48
   Z-Wave                          received "Temperatur Küche " sensor update to 24.9 °C
   Z-Wave                          received "Temperatur Küche " sensor update to 24.9 °C
   Z-Wave                          received "Temperatur Küche " sensor update to 24.9 °C
   Z-Wave                          received "Temperatur Küche " sensor update to 24.9 °C
   Schedule                        Now
   Z-Wave                          controller included module: 168 - Notification Sensor
   Z-Wave                          querying module for encryption support
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.72 °C
   Z-Wave                          starting encryption key exchange with module
   Z-Wave Error                    missing expected node callback ack (168) for nonceRequest (will re-send)
   Z-Wave Error                    controller failed to exit inclusion mode
   Z-Wave                          Syncing - started for "168 - Notification Sensor"
   Z-Wave Error                    Syncing - failed
   Z-Wave Error                    Timeout waiting for "168 - Notification Sensor". Module might be asleep, or is unreachable.
   Z-Wave                          Syncing - started for "168 - Notification Sensor"
   Z-Wave Error                    Syncing - failed
   Z-Wave Error                    Timeout waiting for "168 - Notification Sensor". Module might be asleep, or is unreachable.
   Z-Wave Error                    controller failed to enter inclusion mode

26.07.2020 14:28:56
   Z-Wave                          Syncing - started for "168 - Notification Sensor"
   Schedule                        Now
   Z-Wave Error                    Syncing - failed
   Z-Wave Error                    Timeout waiting for "168 - Notification Sensor". Module might be asleep, or is unreachable.
   Z-Wave Error                    no ack/nak/busy reply (168) for nonceRequest (re-sending)
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.72 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.72 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.72 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.72 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.72 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.72 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.72 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.72 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.72 °C
   Z-Wave                          retrieved module neighbors list: 12, 27, 28, 39, 50, 54, 56, 57, 58, 59, 60, 61, 62, 76, 78, 86, 97, 122, 131, 153, 154, 155, 162
   Z-Wave                          retrieved module neighbors list: 12, 27, 28, 39, 50, 54, 56, 57, 58, 59, 60, 61, 62, 76, 78, 86, 97, 122, 131, 153, 154, 155, 162
   Z-Wave                          started controller inclusion mode with encryption
   Z-Wave                          retrieved module neighbors list: 12, 27, 28, 39, 50, 54, 56, 57, 58, 59, 60, 61, 62, 76, 78, 86, 97, 122, 131, 153, 154, 155, 162
   Z-Wave                          stopped controller inclusion mode
   Z-Wave Error                    the node included has the same ID as a node already in use by Indigo
   Z-Wave Error                    to change the encryption state of the device you must exclude it before re-including it
   Z-Wave                          Syncing - started for "168 - Notification Sensor"
   Z-Wave                          Syncing - retrieved module neighbors list: 12, 27, 28, 39, 50, 54, 56, 57, 58, 59, 60, 61, 62, 76, 78, 86, 97, 122, 131, 153, 154, 155, 162
   Z-Wave                          Syncing - assigning return route to "168 - Notification Sensor"
   Z-Wave                          Syncing - assigned return route
   Z-Wave                          Syncing - retrieved manufacture and model names: Fibaro System - 010F, Smart Implant (FGBS222) - 05021000
   Z-Wave                          Syncing - retrieved protocol version 6.02, app version 5.01
   Z-Wave                          Syncing - retrieved class hierarchy: Routing Slave : Notification Sensor : Notification Sensor (04 : 07 : 01, base 00)
   Z-Wave                          Syncing - retrieved command classes: 20v1 85v1 86v1 8Ev1 55v1 56v1 98v1 59v1 5Av1 5Bv1 5Ev1 9Fv1 60v4 22v1 25v1 31v11 6Cv1 70v1 71v1 72v1 73v1 75v1 7Av1
   Z-Wave                          Syncing - retrieved encrypt commands: - none -
   Z-Wave                          Syncing - retrieved capabilities: routing, beaming, security
   Z-Wave                          Syncing - retrieved multi-endpoint types: 1:(07 : 01), 2:(07 : 01), 3:(21 : 01), 4:(21 : 01), 5:(10 : 01), 6:(10 : 01), 7:(21 : 01)
   Z-Wave                          Syncing - retrieved multi-endpoint classes: 1:[5E 85 8E 59 71 6C 22 98 9F], 2:[5E 85 8E 59 71 6C 22 98 9F], 3:[5E 85 8E 59 31 6C 22 98 9F], 4:[5E 85 8E 59 31 6C 22 98 9F], 5:[5E 25 85 8E 59 75 6C 22 98 9F], 6:[5E 25 85 8E 59 75 6C 22 98 9F], 7:[5E 85 8E 59 31 71 6C 22 98 9F]
   Z-Wave                          Syncing - retrieved group 1 associations: []
   Z-Wave                          Syncing - retrieved group 2 associations: []
   Z-Wave                          Syncing - retrieved group 3 associations: []
   Z-Wave                          Syncing - added group 1 multi association to interface
   Z-Wave                          Syncing - retrieved parameter 20 "Input 1 type" is 2 "Push Button (Enables Scenes)"
   Z-Wave                          Syncing - retrieved parameter 40 "Input 1 scene sending" is 0 "None"
   Z-Wave                          Syncing - retrieved parameter 21 "Input 2 type" is 2 "Push Button (Enables Scenes)"
   Z-Wave                          Syncing - retrieved parameter 41 "Input 2 scene sending" is 0 "None"
   Z-Wave                          Syncing - retrieved parameter 24 "Swap inputs (IN1 and IN2)" is false
   Z-Wave                          Syncing - retrieved parameter 154 "Output 1 type" is 0 "Normally Open"
   Z-Wave                          Syncing - retrieved parameter 156 "Output 1 delayed off" is 0 * 0.1 seconds
   Z-Wave                          Syncing - retrieved parameter 155 "Output 2 type" is 0 "Normally Open"
   Z-Wave                          Syncing - retrieved parameter 157 "Output 2 delayed off" is 0 * 0.1 seconds
   Z-Wave                          Syncing - retrieved parameter 25 "Swap outputs (OUT1 and OUT2)" is false
   Z-Wave                          Syncing - retrieved parameter 66 "Internal temperature interval" is 0 seconds
   Z-Wave                          Syncing - retrieved parameter 65 "Internal temperature sensitivity" is 5 * 0.1°C
   Z-Wave                          Syncing - retrieved parameter 64 "Analog input interval" is 0 seconds
   Z-Wave                          Syncing - retrieved parameter 63 "Analog input sensitivity" is 5 * 0.1 V
   Z-Wave                          Syncing - retrieved parameter 150 "Analog IN1 debounce" is 10 milliseconds
   Z-Wave                          Syncing - retrieved parameter 151 "Analog IN2 debounce" is 10 milliseconds
   Z-Wave                          Syncing - retrieved parameter 68 "External sensor interval" is 0 seconds
   Z-Wave                          Syncing - retrieved parameter 67 "External sensor sensitivity" is 5 * 0.1
   Z-Wave                          Syncing - changed device "166 - Binary IN1" address from undefined to 168
   Z-Wave                          Syncing - changed device "166 - Analog IN1" address from undefined to 168
   Z-Wave                          Syncing - changed device "166 - Binary IN2" address from undefined to 168
   Z-Wave                          Syncing - changed device "166 - Analog IN2" address from undefined to 168
   Z-Wave                          Syncing - changed device "166 - Relay 1" address from undefined to 168
   Z-Wave                          Syncing - changed device "166 - Relay 2" address from undefined to 168
   Z-Wave                          Syncing - changed device "166 - Temperature" address from undefined to 168
   Z-Wave                          Syncing - complete
   Z-Wave                          device "168 - 166 - Binary IN1" parameter 156 "Output 1 delayed off" changed to 20 * 0.1 seconds
   Z-Wave                          device "168 - 166 - Binary IN1" parameter 157 "Output 2 delayed off" changed to 20 * 0.1 seconds
   Z-Wave                          sent "166 - Relay 1" on
   Z-Wave                          received "166 - Relay 1" status update is off

Is it in encryption mode now? How could I verify this?
If not, why is it included unencrypted although I included it using encryption?

The basic question here seems to be, has anyone included that device properly using encryption?
Thanks in advance
Wilhelm

Posted on
Sun Jul 26, 2020 7:13 am
Umtauscher offline
User avatar
Posts: 542
Joined: Oct 03, 2014
Location: Cologne, Germany

Re: Fibaro Smart Implant - encrypted?

So I removed and included it again.
Encyption seems to be set now, but syncing fails - tried 4 times.
The devive is permanently powerd btw.

Code: Select all
   Z-Wave                          started controller inclusion mode with encryption

26.07.2020 15:02:00
   Schedule                        Now
   Z-Wave                          controller included module: 170 - Notification Sensor
   Z-Wave                          querying module for encryption support
   Z-Wave                          starting encryption key exchange with module
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.90 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.90 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.90 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.90 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.90 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.90 °C
   Z-Wave                          received "Thermostat Studio links" temperature update to 23.90 °C
   Z-Wave                          completed encryption key exchange with module
   Z-Wave                          stopped controller inclusion mode
   Z-Wave                          received "Thermostat Flur" temperature update to 22.64 °C
   Z-Wave                          received "Temperatur Gästeklo " sensor update to 23.4 °C

26.07.2020 15:02:50
   Z-Wave                          Syncing - started for "170 - Notification Sensor"
   Z-Wave                          Syncing - retrieved module neighbors list: 3, 12, 27, 28, 39, 50, 54, 56, 57, 58, 59, 60, 61, 62, 76, 78, 86, 97, 122, 131, 153, 154, 155, 162, 163, 165
   Z-Wave                          Syncing - assigning return route to "170 - Notification Sensor"
   Z-Wave                          Syncing - assigned return route
   Z-Wave                          Syncing - retrieved manufacture and model names: Fibaro System - 010F, Smart Implant (FGBS222) - 05021000
   Z-Wave                          Syncing - retrieved protocol version 6.02, app version 5.01
   Schedule                        Now
   Z-Wave                          Syncing - retrieved class hierarchy: Routing Slave : Notification Sensor : Notification Sensor (04 : 07 : 01, base 00)
   Z-Wave                          Syncing - retrieved command classes: 20v1 85v1 86v1 8Ev1 55v1 56v1 98v1 59v1 5Av1 5Bv1 5Ev1 9Fv1 60v4 22v1 25v1 31v11 6Cv1 70v1 71v1 72v1 73v1 75v1 7Av1
   Z-Wave                          Syncing - retrieved encrypt commands: 60 25 86 31 8E 70 71 72 73 75 59 5A 5B 7A 85
   Z-Wave                          Syncing - retrieved capabilities: routing, beaming, security
   Z-Wave                          received "Helligkeit Gästeklo" sensor update to 364 lux
   Z-Wave                          received "Temperatur  Badezimmer" sensor update to 25.0 °C
   Z-Wave                          received "Helligkeit  Badezimmer" sensor update to 0 lux

26.07.2020 15:04:00
   Schedule                        Now
   Z-Wave                          Syncing - retrieved multi-endpoint types: 1:(07 : 01), 2:(07 : 01), 3:(21 : 01), 4:(21 : 01), 5:(10 : 01), 6:(10 : 01), 7:(21 : 01)
   Z-Wave                          Syncing - retrieved multi-endpoint classes: 1:[5E 6C 22 98 9F], 2:[5E 6C 22 98 9F], 3:[5E 6C 22 98 9F], 4:[5E 6C 22 98 9F], 5:[5E 6C 22 98 9F], 6:[5E 6C 22 98 9F], 7:[5E 6C 22 98 9F]
   Z-Wave                          Syncing - retrieved group 1 associations: []
   Z-Wave                          Syncing - retrieved group 2 associations: []
   Z-Wave                          Syncing - retrieved group 3 associations: []
   Z-Wave                          Syncing - added group 1 multi association to interface
   Z-Wave                          Syncing - retrieved parameter 20 "Input 1 type" is 2 "Push Button (Enables Scenes)"
   Z-Wave                          Syncing - retrieved parameter 40 "Input 1 scene sending" is 0 "None"
   Z-Wave                          Syncing - retrieved parameter 21 "Input 2 type" is 2 "Push Button (Enables Scenes)"
   Schedule                        Now
   Z-Wave                          Syncing - retrieved parameter 41 "Input 2 scene sending" is 0 "None"
   Z-Wave                          Syncing - retrieved parameter 24 "Swap inputs (IN1 and IN2)" is false
   Z-Wave                          Syncing - retrieved parameter 154 "Output 1 type" is 0 "Normally Open"
   Z-Wave                          received "Helligkeit 2.OG" sensor update to 46 lux
   Z-Wave                          received "Helligkeit Küche" sensor update to 13 lux
   Z-Wave                          Syncing - retrieved parameter 156 "Output 1 delayed off" is 0 * 0.1 seconds
   Z-Wave                          Syncing - retrieved parameter 155 "Output 2 type" is 0 "Normally Open"
   Z-Wave                          Syncing - retrieved parameter 157 "Output 2 delayed off" is 0 * 0.1 seconds
   Schedule                        Now
   Z-Wave                          received "Bewegungsmelder  1.OG" status update is on
   Trigger                         Treppenhaus 1.OG ein
   Z-Wave Error                    Syncing - failed
   Z-Wave Error                    Timeout waiting for "170 - Notification Sensor". Module might be asleep, or is unreachable.

26.07.2020 15:06:28
   Z-Wave                          Syncing - started for "170 - Notification Sensor"
   Z-Wave                          received "Tilt/Tamper 1.OG" status update is off
   Z-Wave                          received "Bewegungsmelder  1.OG" status update is off
   Trigger                         Treppenhaus 1.OG aus
   Z-Wave Error                    Syncing - failed
   Z-Wave Error                    Timeout waiting for "170 - Notification Sensor". Module might be asleep, or is unreachable.
   Z-Wave                          sent "Treppenhaus OG" on
   Z-Wave                          retrieved module neighbors list: 3, 12, 27, 28, 39, 50, 54, 56, 57, 58, 59, 60, 61, 62, 76, 78, 86, 97, 122, 131, 153, 154, 155, 162, 163, 165
   Z-Wave                          sent "Treppenhaus OG" off
   Z-Wave                          Syncing - started for "170 - Notification Sensor"
   Z-Wave                          Syncing - retrieved module neighbors list: 3, 12, 27, 28, 39, 50, 54, 56, 57, 58, 59, 60, 61, 62, 76, 78, 86, 97, 122, 131, 153, 154, 155, 162, 163, 165
   Z-Wave                          Syncing - assigning return route to "170 - Notification Sensor"
   Z-Wave                          Syncing - assigned return route
   Schedule                        Now
   Z-Wave                          Syncing - retrieved manufacture and model names: Fibaro System - 010F, Smart Implant (FGBS222) - 05021000
   Z-Wave                          received "Eingangstür" status update is on
   Z-Wave Error                    Syncing - failed
   Z-Wave Error                    Timeout waiting for "170 - Notification Sensor". Module might be asleep, or is unreachable.
   Z-Wave                          received "Temperatur Küche " sensor update to 24.8 °C
   Z-Wave                          Syncing - started for "170 - Notification Sensor"
   Z-Wave Error                    Syncing - failed
   Z-Wave Error                    Timeout waiting for "170 - Notification Sensor". Module might be asleep, or is unreachable.
   Schedule                        Now
   Z-Wave                          Syncing - started for "170 - Notification Sensor"
   Z-Wave                          Syncing - retrieved module neighbors list: 3, 12, 27, 28, 39, 50, 54, 56, 57, 58, 59, 60, 61, 62, 76, 78, 86, 97, 122, 131, 153, 154, 155, 162, 163, 165
   Z-Wave                          Syncing - retrieved module neighbors list: 3, 12, 27, 28, 39, 50, 54, 56, 57, 58, 59, 60, 61, 62, 76, 78, 86, 97, 122, 131, 153, 154, 155, 162, 163, 165
   Z-Wave                          Syncing - assigning return route to "170 - Notification Sensor"

26.07.2020 15:08:25
   Z-Wave                          Syncing - retrieved manufacture and model names: Fibaro System - 010F, Smart Implant (FGBS222) - 05021000
   Z-Wave                          received "Eingangstür" status update is off
   Z-Wave                          received "Eingangstür" status update is on
   Z-Wave Error                    Syncing - failed
   Z-Wave Error                    Timeout waiting for "170 - Notification Sensor". Module might be asleep, or is unreachable.
   Z-Wave                          Syncing - started for "170 - Notification Sensor"
   Z-Wave                          received "Eingangstür" status update is off
   Schedule                        Now
   Z-Wave Error                    Syncing - failed
   Z-Wave Error                    Timeout waiting for "170 - Notification Sensor". Module might be asleep, or is unreachable.

26.07.2020 15:09:50
   Z-Wave                          received "Temperatur 2. OG" sensor update to 26.2 °C
   Schedule                        Now

Posted on
Sun Jul 26, 2020 7:20 am
Umtauscher offline
User avatar
Posts: 542
Joined: Oct 03, 2014
Location: Cologne, Germany

Re: Fibaro Smart Implant - encrypted?

another attempt: Syncing now seems to have suceeded

Code: Select all
rted for "170 - Notification Sensor"
   Z-Wave                          Syncing - retrieved module neighbors list: 3, 12, 27, 28, 39, 50, 54, 56, 57, 58, 59, 60, 61, 62, 76, 78, 86, 97, 122, 131, 153, 154, 155, 162, 163, 165
   Z-Wave                          Syncing - assigning return route to "170 - Notification Sensor"
   Z-Wave                          Syncing - assigned return route
   Z-Wave                          Syncing - retrieved manufacture and model names: Fibaro System - 010F, Smart Implant (FGBS222) - 05021000
   Z-Wave                          Syncing - retrieved protocol version 6.02, app version 5.01
   Schedule                        Now
   Z-Wave                          Syncing - retrieved class hierarchy: Routing Slave : Notification Sensor : Notification Sensor (04 : 07 : 01, base 00)
   Z-Wave                          Syncing - retrieved command classes: 20v1 85v1 86v1 8Ev1 55v1 56v1 98v1 59v1 5Av1 5Bv1 5Ev1 9Fv1 60v4 22v1 25v1 31v11 6Cv1 70v1 71v1 72v1 73v1 75v1 7Av1
   Z-Wave                          Syncing - retrieved encrypt commands: 85 86 8E 59 5A 5B 60 25 71 70 31 72 73 75 7A
   Z-Wave                          Syncing - retrieved capabilities: routing, beaming, security

26.07.2020 15:13:23
   Z-Wave                          received "Helligkeit Gästeklo" sensor update to 368 lux
   Z-Wave                          received "Gästeklo Bewegungsmelder" status update is on
   Trigger                         Bewegungsmelder Gästeklo
   Action Group                    Musiccast Gästeklo On
   Virtual Devices                 sent "Lautsprecher Gästeklo" on
   Z-Wave                          received "Temperatur  Badezimmer" sensor update to 25.0 °C
   Z-Wave                          received "Temperatur  Badezimmer" sensor update to 25.0 °C
   Z-Wave                          received "Helligkeit  Badezimmer" sensor update to 0 lux

26.07.2020 15:14:00
   Schedule                        Now
   Z-Wave                          Syncing - retrieved multi-endpoint types: 1:(07 : 01), 2:(07 : 01), 3:(21 : 01), 4:(21 : 01), 5:(10 : 01), 6:(10 : 01), 7:(21 : 01)
   Z-Wave                          Syncing - retrieved multi-endpoint classes: 1:[5E 6C 22 98 9F], 2:[5E 6C 22 98 9F], 3:[5E 6C 22 98 9F], 4:[5E 6C 22 98 9F], 5:[5E 6C 22 98 9F], 6:[5E 6C 22 98 9F], 7:[5E 6C 22 98 9F]
   Z-Wave                          received "Temperatur Gästeklo " sensor update to 23.4 °C
   Z-Wave                          Syncing - retrieved group 1 associations: []
   Z-Wave                          Syncing - retrieved group 2 associations: []
   Z-Wave                          Syncing - retrieved group 3 associations: []
   Z-Wave                          Syncing - added group 1 multi association to interface
   Z-Wave                          Syncing - retrieved parameter 20 "Input 1 type" is 2 "Push Button (Enables Scenes)"
   Z-Wave                          Syncing - retrieved parameter 40 "Input 1 scene sending" is 0 "None"
   Z-Wave                          Syncing - retrieved parameter 21 "Input 2 type" is 2 "Push Button (Enables Scenes)"
   Z-Wave                          Syncing - retrieved parameter 41 "Input 2 scene sending" is 0 "None"
   Schedule                        Now
   Z-Wave                          Syncing - retrieved parameter 24 "Swap inputs (IN1 and IN2)" is false
   Z-Wave                          Syncing - retrieved parameter 154 "Output 1 type" is 0 "Normally Open"
   Z-Wave                          Syncing - retrieved parameter 156 "Output 1 delayed off" is 0 * 0.1 seconds
   Z-Wave                          received "Helligkeit Küche" sensor update to 32 lux
   Z-Wave                          received "Helligkeit 2.OG" sensor update to 97 lux
   Z-Wave                          Syncing - retrieved parameter 155 "Output 2 type" is 0 "Normally Open"
   Z-Wave                          Syncing - retrieved parameter 157 "Output 2 delayed off" is 0 * 0.1 seconds
   Z-Wave                          received "Gästeklo Bewegungsmelder" status update is off
   Trigger                         Bewegungsmelder Gästeklo aus
   Action Group                    Musiccast Gästeklo Off
   Virtual Devices                 sent "Lautsprecher Gästeklo" off
   Z-Wave                          received "Deckenlampe Gaesteklo " status update is off (from associate)
   Z-Wave                          received "Helligkeit Gästeklo" sensor update to 37 lux
   Z-Wave                          Syncing - retrieved parameter 25 "Swap outputs (OUT1 and OUT2)" is false
   Z-Wave                          Syncing - retrieved parameter 66 "Internal temperature interval" is 0 seconds
   Z-Wave                          Syncing - retrieved parameter 65 "Internal temperature sensitivity" is 5 * 0.1°C
   Schedule                        Now
   Z-Wave                          Syncing - retrieved parameter 64 "Analog input interval" is 0 seconds
   Z-Wave                          Syncing - retrieved parameter 63 "Analog input sensitivity" is 5 * 0.1 V
   Z-Wave                          Syncing - retrieved parameter 150 "Analog IN1 debounce" is 10 milliseconds
   Z-Wave                          received "Thermostat Studio rechts" temperature update to 24.17 °C
   Z-Wave                          Syncing - retrieved parameter 151 "Analog IN2 debounce" is 10 milliseconds
   Z-Wave Error                    RCVD encryptedPacket: unexpected sequence byte 47
   Z-Wave Error                    RCVD encryptedPacket:  full raw packet 01 20 00 04 00 AA 1A 98 81 84 38 25 67 14 3D 40 8C 9E FC 02 38 FD 73 77 C0 7F C0 55 7A CC 3D FD 6E FA
   Z-Wave Error                    RCVD encryptedPacket: encrypted packet 9E FC 02 38 FD 73 77
   Z-Wave Error                    RCVD encryptedPacket: decrypted packet 47 5F 83 C0 05 8D 94
   Z-Wave Error                    encrypted command received from node ID 170 has invalid CBC-MAC value (ignoring)
   Z-Wave                          Syncing - retrieved parameter 68 "External sensor interval" is 0 seconds
   Z-Wave                          Syncing - retrieved parameter 67 "External sensor sensitivity" is 5 * 0.1
   Z-Wave                          Syncing - changed device "166 - Binary IN1" address from undefined to 170
   Z-Wave                          Syncing - changed device "166 - Analog IN1" address from undefined to 170
   Z-Wave                          Syncing - changed device "166 - Binary IN2" address from undefined to 170
   Z-Wave                          Syncing - changed device "166 - Analog IN2" address from undefined to 170
   Z-Wave                          Syncing - changed device "166 - Relay 1" address from undefined to 170
   Z-Wave                          Syncing - changed device "166 - Relay 2" address from undefined to 170
   Z-Wave                          Syncing - changed device "166 - Temperature" address from undefined to 170
   Z-Wave                          Syncing - complete
   Z-Wave                          received "Temperatur Wassersensor" sensor update to 25.24 °C
   Z-Wave                          received "Tilt/Tamper Wassersensor" status update is on
   Z-Wave                          received "Wassersensor" status update is off
   Z-Wave                          received "103 - Wassersensor" status update battery level 5%
   Schedule                        Now
   Z-Wave                          received "Thermostat Keller" mode is heat
   Z-Wave                          received "Thermostat Keller" mode is heat
   Z-Wave                          received "Thermostat Keller" temperature update to 19.99 °C
   Z-Wave                          received "Thermostat Keller" heat setpoint is 14.0 °C

26.07.2020 15:17:37
   Z-Wave                          received "Temperatur Küche " sensor update to 24.7 °C
   Z-Wave                          device "170 - 166 - Binary IN1" parameter 20 "Input 1 type" changed to 1 "Normally Open"
   Z-Wave                          device "170 - 166 - Binary IN1" parameter 21 "Input 2 type" changed to 1 "Normally Open"
   Z-Wave                          device "170 - 166 - Binary IN1" parameter 156 "Output 1 delayed off" changed to 20 * 0.1 seconds
   Z-Wave                          device "170 - 166 - Binary IN1" parameter 157 "Output 2 delayed off" changed to 20 * 0.1 seconds
   Schedule                        Now

26.07.2020 15:19:00
   Schedule                        Now

... and now the error message when trying to switch the relais is back:
Z-Wave Error device "166 - Relay 1" does not support on command

This over time is the 4th device I try to include with encrytion and none of them is properly running with encryption:

1. Fibaro Keyfob
2. Popp siren
3. Aeotec keyfob
4. Fibaro smart implant

Posted on
Sun Jul 26, 2020 10:47 am
Umtauscher offline
User avatar
Posts: 542
Joined: Oct 03, 2014
Location: Cologne, Germany

Re: Fibaro Smart Implant - encrypted?

Talking to myself again - sorry

Reading the Fibaro documentation I found that after "power on" this device signales by LED wether it is configured without encryption (green) or with encryption (magenta).
So Indigo cannot bring this device to encrypted mode, even if it says it does.

Nevertheless including it trying to encrypt stops the relays from working.

Posted on
Sun Jul 26, 2020 10:52 am
Umtauscher offline
User avatar
Posts: 542
Joined: Oct 03, 2014
Location: Cologne, Germany

Re: Fibaro Smart Implant - encrypted?

and here's the difference:
Code: Select all
Inclusion encrypted:
 Z-Wave                          Syncing - retrieved multi-endpoint classes:
                              1:[5E 6C 22 98 9F],
                              2:[5E 6C 22 98 9F],
                              3:[5E 6C 22 98 9F],
                              4:[5E 6C 22 98 9F],
                              5:[5E 6C 22 98 9F],
                              6:[5E 6C 22 98 9F],
                              7:[5E 6C 22 98 9F]
 
inclusion unencrypted:

Z-Wave                          Syncing - retrieved multi-endpoint classes:
                              1:[5E 85 8E 59 71 6C 22 98 9F],
                              2:[5E 85 8E 59 71 6C 22 98 9F],
                              3:[5E 85 8E 59 31 6C 22 98 9F],
                              4:[5E 85 8E 59 31 6C 22 98 9F],
                              5:[5E 25 85 8E 59 75 6C 22 98 9F],
                              6:[5E 25 85 8E 59 75 6C 22 98 9F],
                              7:[5E 85 8E 59 31 71 6C 22 98 9F]
 

but I really don't know what that means...

Posted on
Mon Jul 27, 2020 1:54 am
howartp offline
Posts: 4139
Joined: Jan 09, 2014
Location: West Yorkshire, UK

Re: Fibaro Smart Implant - encrypted?

I’ll have a look at this when I get to my PC.


Sent from my iPhone using Tapatalk Pro

Page 1 of 1

Who is online

Users browsing this forum: No registered users and 1 guest

cron