[ANSWERED]: Linear GD00Z-4 GD00Z-4 Z-Wave Garage Door Opener

Appreciate the quick responses. Looks like my install is complete then.

Matt - My apologies for not replying sooner - I just saw your post with the update, I installed and all is working well.

Thanks for getting this fix in!!!

Appreciate it.

Joe

HAs anyone else experienced any issues using the latest update and the Garage Door Opener? Several times it seems to go No Ack. Sometimes I can just resync and it fixes it but tonight that isn't working and I may need to remove it and Add it back in

I haven't had any issues


Sent from my iPhone using Tapatalk

Its working fine here.

[matt (support)]

Indigo v7.0.3 is now available and includes support for the Z-Wave Linear GD00Z-4 garage door controller.

What is the expected behavior in 7.0.3? I sync with encryption, the device is discovered and sync'd. The status always says "on", and when I press the "off" button, nothing happens. However, if I press the "on" button, the unit does the beeping as expected. If I lower and raise the door with the actual garage door button, the status never changes in Indigo, and I don't think I see an update message in the logs.

Does the "off" button actually do anything?

In summary .. non-rambling a day later:

1. My stuff sat for so long, I think the tilt sensor and main unit lost pairing.
2. I re-paired the tilt sensor and main unit per the instructions below
3. I paired the main unit with Indigo, per the instruction above, using encryption in Indigo.

Those steps make it so I can open and close the unit via Indigo, but the status/state NEVER changes unless I am doing a status request. The status request is accurate, as it reports the state of either open, closed, opening, or closing.

Things I noticed that are puzzling, and potentially buggy:

1. The Edit Device Settings option does not show any real options, UNLESS I try a re-sync and define a second time (even though the unit was working). After this, I now have an option to adjust polling frequency, even though it doesn't appear to be working.


Reset process:

1.) Reset the GD00Z-4 controller to factory
- press the pairing button 5 times
2.) Pair the Tilt Sensor if in doubt
- install tilt sensor
- hold controller button for 7'ish seconds until it beeps
- open garage door and unit should beep/flash as door opens
3.) Close garage door
4.) Pair GD00Z-4 Controller with Indigo (encrypted)
5.) Open garage
6.) Close garage
7.) Status requests now work, but only if I ask for them.


Thanks,
James

[matt (support)]

Hi James,

Copy/paste the Event Log window results into a reply post showing a re-sync of the device as well as you open/closing the garage door a couple of times from Indigo.

Define & Sync output for the device (It was already sync'd, and had the extra "polling option" at this point.) If You want to see a fresh process, I can do that as well.

Jan 29, 2017, 11:11:18 AM
Z-Wave Debug intiatingSyncUI (timeout in 1500 seconds)
Z-Wave Syncing - started for "Main Garage Door"
Z-Wave Debug SENT getNodeNeighbors: 01 06 00 80 0F 01 01 76
Z-Wave Debug RCVD getNodeNeighbors: 01 20 01 80 9E 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40
Z-Wave Debug . . getNodeNeighbors: nodeId 015, neighbors: 2, 3, 4, 5, 8, 16
Z-Wave Syncing - retrieved module neighbors list: 2, 3, 4, 5, 8, 16
Z-Wave Syncing - assigning return route to "015 - Main Garage Door"
Z-Wave Debug SENT assignReturnRoute: 01 05 00 46 0F 01 B2
Z-Wave Debug RCVD assignReturnRoute: 01 04 01 46 01 BD
Z-Wave Debug RCVD assignReturnRoute: 01 05 00 46 01 00 BD
Z-Wave Debug . . assignReturnRoute: node 015, success 1
Z-Wave Syncing - assigned return route
Z-Wave Debug SENT requestNodeInfo: 01 06 00 60 0F 24 05 B7
Z-Wave Debug RCVD nodeInfoFrame: 01 0C 00 49 84 0F 06 04 40 07 72 98 5A C4
Z-Wave Debug . . nodeInfoFrame: node 015, combined class list: 20v1 98v1 72v1 5Av1 66v1
Z-Wave Debug SENT nonceRequest: 01 09 00 13 0F 02 98 40 25 06 13
Z-Wave Debug RCVD nonceReport: node 015, nonce FD B1 F8 3E 67 5A 11 60
Z-Wave Debug SENT requestEncryptedCmdClasses: 98 02 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce 32 3A 09 45 72 40 A9 56 (saving)
Z-Wave Debug RCVD nonceFetch: node 015
Z-Wave Debug SENT nonceReport: 01 11 00 13 0F 0A 98 80 DF F5 E0 FF C9 4D 7B DB 25 08 DC
Z-Wave Debug RCVD encryptedPacket: 00 98 03 00 86 66 22 71 85 EF (decrypted)
Z-Wave Debug RCVD requestEncryptedCmdClasses: 01 0F 00 04 00 0F 09 98 03 00 86 66 22 71 85 EF FF
Z-Wave Debug RCVD requestEncryptedCmdClasses: node 015, classes 86 66 22 71 85 EF
Z-Wave Debug SENT requestManufactureInfo: 01 09 00 13 0F 02 72 04 25 09 B2
Z-Wave Debug RCVD requestManufactureInfo: 01 0E 00 04 00 0F 08 72 05 01 4F 47 44 30 30 C8
Z-Wave Debug . . requestManufactureInfo: node 015, manufacturerId 014F, productId 47443030
Z-Wave Debug . . requestManufactureInfo: LinearLinc, Garage Door Controller (GD00Z-4)
Z-Wave Syncing - retrieved manufacture and model names: LinearLinc - 014F, Garage Door Controller (GD00Z-4) - 47443030
Z-Wave Debug SENT requestVersInfoGen: 86 11 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce 14 9B 7E 8E 7C B0 11 9A (saving)
Z-Wave Debug timeout waiting for reply from module (retrying)
Z-Wave Debug SENT nonceRequest: 01 09 00 13 0F 02 98 40 25 0B 1E
Z-Wave Debug RCVD nonceReport: node 015, nonce 80 D0 35 85 C0 9E F3 EE
Z-Wave Debug SENT requestVersInfoGen: 86 11 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce EB 1C C6 E6 E1 55 8D 10 (saving)
Z-Wave Debug RCVD nonceFetch: node 015
Z-Wave Debug SENT nonceReport: 01 11 00 13 0F 0A 98 80 B9 18 C5 81 3E 3E B6 10 25 0D 8B
Z-Wave Debug RCVD encryptedPacket: 00 86 12 03 03 43 01 02 01 01 01 02 (decrypted)
Z-Wave Debug RCVD requestVersInfoGen: 01 11 00 04 00 0F 0B 86 12 03 03 43 01 02 01 01 01 02 FF
Z-Wave Debug . . requestVersInfoGen: node 015, protoVers 3.67, appVers 1.02
Z-Wave Syncing - retrieved protocol version 3.67, app version 1.02
Z-Wave Syncing - retrieved class hierarchy: Routing Slave : Entry Control : Secure Barrier Add-On (04 : 40 : 07, base 66)
Z-Wave Syncing - retrieved command classes: 20v1 22v1 86v1 66v1 71v1 72v1 98v1 5Av1 85v1
Z-Wave Syncing - retrieved encrypt commands: 71 22 85 66 86
Z-Wave Syncing - retrieved capabilities: routing, beaming, security
Z-Wave Debug SENT requestAssociationGroupCount: 85 05 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce 86 C6 49 09 30 BA BC BF (saving)
Z-Wave Debug timeout waiting for reply from module (retrying)
Z-Wave Debug SENT nonceRequest: 01 09 00 13 0F 02 98 40 25 0F 1A
Z-Wave Debug RCVD nonceReport: node 015, nonce 58 82 F4 6E 06 89 14 0E
Z-Wave Debug SENT requestAssociationGroupCount: 85 05 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce EB 71 C9 4C C8 4A EF 09 (saving)
Z-Wave Debug RCVD nonceFetch: node 015
Z-Wave Debug SENT nonceReport: 01 11 00 13 0F 0A 98 80 7F 5C 40 3B 4F 99 BF A9 25 11 4C
Z-Wave Debug RCVD encryptedPacket: 00 85 06 01 (decrypted)
Z-Wave Debug RCVD requestAssociationGroupCount: 01 09 00 04 00 0F 03 85 06 01 FF
Z-Wave Debug . . requestAssociationGroupCount: node 015, group count: 1
Z-Wave Debug SENT requestAssociations: 85 02 01 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce E2 AE 25 E3 3D D4 C5 58 (saving)
Z-Wave Debug timeout waiting for reply from module (retrying)
Z-Wave Debug SENT nonceRequest: 01 09 00 13 0F 02 98 40 25 13 06
Z-Wave Debug RCVD nonceReport: node 015, nonce 94 A3 8E 80 5C 61 B5 A5
Z-Wave Debug SENT requestAssociations: 85 02 01 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce C6 0E 2C FD AF 81 2C B2 (saving)
Z-Wave Debug RCVD nonceFetch: node 015
Z-Wave Debug SENT nonceReport: 01 11 00 13 0F 0A 98 80 65 E2 63 E4 54 E2 F4 D0 25 15 42
Z-Wave Debug RCVD encryptedPacket: 00 85 03 01 01 00 (decrypted)
Z-Wave Debug RCVD requestAssociations: 01 0B 00 04 00 0F 05 85 03 01 01 00 FF
Z-Wave Debug . . requestAssociations: node 015, group: 1, num associations: 0, max associations: 1, replies left: 0
Z-Wave Debug . . requestAssociations: node 015, group: 1, associations: []
Z-Wave Syncing - retrieved group 1 associations: []
Z-Wave Debug SENT addInterfaceAssociation: 85 01 01 01 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce 76 8F 01 71 BC 52 F2 FB (saving)
Z-Wave Syncing - added group 1 association to interface
Z-Wave Debug . . addInterfaceAssociation: node 015, group: 1, associations: [1]
Z-Wave Syncing - complete
Z-Wave Debug stopped polling of "015 - Main Garage Door"
Z-Wave Debug started polling of "015 - Main Garage Door" approx every 300 seconds
Z-Wave Debug SENT requestBarrierStatus: 66 02 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce 64 6C C6 42 AF 33 2B 5B (saving)
Z-Wave Debug terminatingSyncUI
Z-Wave sent "Main Garage Door" status request
Z-Wave Debug RCVD nonceFetch: node 015
Z-Wave Debug SENT nonceReport: 01 11 00 13 0F 0A 98 80 65 E2 63 E4 54 E2 F4 D0 25 18 4F
Z-Wave Debug RCVD encryptedPacket: 00 66 03 FF (decrypted)
Z-Wave Debug RCVD requestBarrierStatus: 01 09 00 04 00 0F 03 66 03 FF FF
Z-Wave Debug . . requestBarrierStatus: node 015, endpoint None, value 255
Z-Wave received "Main Garage Door" status update is open


Open command from Indigo (Door did open):

Jan 29, 2017, 11:04:10 AM
Z-Wave Debug SENT nonceRequest: 01 09 00 13 0F 02 98 40 25 F2 E7
Z-Wave Debug RCVD nonceReport: node 015, nonce B5 16 AD EA 5D 5D A2 D7
Z-Wave Debug SENT setBarrierValue: 66 01 FF (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce 22 DC 68 B6 B7 6F 3C 92 (saving)
Z-Wave sent "Main Garage Door" open

Close command from Indigo (Door did close):

Jan 29, 2017, 11:05:18 AM
Z-Wave Debug SENT nonceRequest: 01 09 00 13 0F 02 98 40 25 F4 E1
Z-Wave Debug RCVD nonceReport: node 015, nonce 99 60 24 83 16 F9 20 19
Z-Wave Debug SENT setBarrierValue: 66 01 00 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce 7A A6 D0 20 C3 B8 05 C0 (saving)
Z-Wave sent "Main Garage Door" close



Open command from Indigo again:
Z-Wave Debug SENT nonceRequest: 01 09 00 13 0F 02 98 40 25 F6 E3
Z-Wave Debug RCVD nonceReport: node 015, nonce 41 1F 71 F4 C8 6B 2E D8
Z-Wave Debug SENT setBarrierValue: 66 01 FF (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce 92 C3 90 2A CF 6B 12 54 (saving)
Z-Wave sent "Main Garage Door" open


Close command from Indigo again:
Z-Wave Debug SENT nonceRequest: 01 09 00 13 0F 02 98 40 25 FD E8
Z-Wave Debug RCVD nonceReport: node 015, nonce 09 28 80 05 D0 42 14 95
Z-Wave Debug SENT setBarrierValue: 66 01 00 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce 49 E3 23 F2 2B 0B E6 69 (saving)
Z-Wave sent "Main Garage Door" close


Status request from Indigo (Response is accurate):
Jan 29, 2017, 11:09:19 AM
Z-Wave Debug SENT nonceRequest: 01 09 00 13 0F 02 98 40 25 02 17
Z-Wave Debug RCVD nonceReport: node 015, nonce EE 37 8D 4D 88 BD 87 0B
Z-Wave Debug SENT requestBarrierStatus: 66 02 (encrypted)
Z-Wave Debug RCVD nonceReport: node 015, nonce 14 1E 16 E1 5B 09 9B B9 (saving)
Z-Wave sent "Main Garage Door" status request
Z-Wave Debug RCVD nonceFetch: node 015
Z-Wave Debug SENT nonceReport: 01 11 00 13 0F 0A 98 80 A0 93 DC 38 E1 B7 F1 70 25 04 C1
Z-Wave Debug RCVD encryptedPacket: 00 66 03 00 (decrypted)
Z-Wave Debug RCVD requestBarrierStatus: 01 09 00 04 00 0F 03 66 03 00 FF
Z-Wave Debug . . requestBarrierStatus: node 015, endpoint None, value 0
Z-Wave received "Main Garage Door" status update is closed

[matt (support)]

Yours seems to be responding to commands but, despite Indigo adding an association for group 1 back to the Z-Stick, it isn't broadcasting out barrier status changed commands as the door transitions between states.

I wonder if this is a firmware difference and your version doesn't support that. Based on your log you have version 1.02. I'm not sure what version other users have.

Can other folks on this thread that have their GD00Z working check the version number shown in the device settings dialog?

Bummer! If that turns out to be the issue, I wonder if I can upgrade the version I may contact Linear.

Can other folks on this thread that have their GD00Z working check the version number shown in the device settings dialog?

My GD00Z-4 reports "Garage Door Controller (NGD00Z), firmware 2.00" Running Indigo 7 on a headless Mac Mini late 2012; 2.3 ghz i7; 16g memory model 6,2. Security Spy 4 (7 cameras) is also running on that machine.

I think this definitely justifies a contact to Linear for detail. Im hopeful its a field upgradeable firmware, but I am not optimistic.

Mine is actually a GD-00Z-1, and reports firmware version 1.01. It only has ON and OFF states.
I'm still on 7.0.2. Will 7.0.3 change my status reports?

Jim