If you have a newer version of Jandy system firmware, you may be able to enable cooling using the system menu and configuring your solar as a heat pump in chill mode.
Your other option would be to replace the solar temperature sensor with a resistor to make the system think the roof temp is always hot. You would then be able to turn on the solar heat at night and the system would think it was heating and run the solar as long as the setpoint was higher than the water temperature. You could then use Indigo to monitor the water temperature and turn the solar heating off when the water reaches your desired temperature.
hamw wrote:My pump needs to be replaced. I am thinking of a two speed pump, and saw that the plugin supports "PUMP" and "PUMPLO". I guess that means that a two speed pump is supported?
Anyone have a pump recommendation? I posted on TroublefreePool.com and saw a recommendation for an AO Smith B2983 hi efficiency pump, but y'all's thoughts would be appreciated too. If this is a little off topic, feel free to PM me.
Thanks!
doug@dynamic.com wrote:I am working on developing a plug-in for my Niles GXR2 whole home audio system. It is connected via RS-232. I talk to it now with shell scripts to set and obtain data. I notice that your Jandy plug-in uses the same type of serial connection. I was wondering if any of your source code for your plug-in might be available as a basis for my development and communications.
Doug
doug@dynamic.com wrote:So your plugin would work with the new iaqualink that has the iPad app? I was thinking of upgrading my old Jandy PDA system for remote control of a remote pool at a second location. If it is TCP based, I assume I could use Indigo on my home net to connect to Jandy at the remote location by allowing that traffic through the various firewalls.
Doug
Reloading plugin "Autelis Jandy 1.2.0"
Stopping plugin "Autelis Jandy 1.2.0" (pid 40868)
Stopped plugin "Autelis Jandy 1.2.0"
Starting plugin "Autelis Jandy 1.2.0" (pid 40891)
Started plugin "Autelis Jandy 1.2.0"
****note no connection on port 6000****
May 26, 2013 11:08:03 PM
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Schedule _delayed_action_11
Autelis Jandy Debug TX: #AUX5=0
Autelis Jandy Debug Error: <type 'exceptions.AttributeError'>
Autelis Jandy Error Error in plugin execution ExecuteAction:
Traceback (most recent call last):
File "plugin.py", line 63, in actionAux
File "/Library/Application Support/Perceptive Automation/Indigo 6/Plugins/AutelisJandy.indigoPlugin/Contents/Server Plugin/Autelis.py", line 180, in actionGeneric
File "/Library/Application Support/Perceptive Automation/Indigo 6/Plugins/AutelisJandy.indigoPlugin/Contents/Server Plugin/Autelis.py", line 130, in sendMessage
File "/Library/Application Support/Perceptive Automation/Indigo 6/Plugins/AutelisJandy.indigoPlugin/Contents/Server Plugin/Autelis.py", line 115, in closeConnection
<type 'exceptions.AttributeError'>: 'NoneType' object has no attribute 'close'
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Reloading plugin "Autelis Jandy 1.2.0"
Stopping plugin "Autelis Jandy 1.2.0" (pid 40891)
Autelis Jandy Debug Method: stopConcurrentThread
Autelis Jandy Debug Method: stopConcurrentThread
Stopped plugin "Autelis Jandy 1.2.0"
Starting plugin "Autelis Jandy 1.2.0" (pid 40896)
Started plugin "Autelis Jandy 1.2.0"
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
hamw wrote:The new plugin version sounds super! It's just in time for my current issue, my Jandy ColorSplash light. In order to change the light's color, the light has to be selected in "equipment on/off", and then one has to press "off/on" and the "off/on" needs to be sent within 5 seconds, otherwise it goes back to white. I've tried using the Autelis web interface and it can't respond fast enough to "off/on" to get the light to advance to the next color. Maybe there a workaround with the new functionality you've built in to the plugin?
Thanks again for your great work with this plugin!
--Edit--
Tried d/l the plugin and running it. I am on Beta 7. Do I need Beta 8 for this? I tried recreating the "Pool" device with no success, and putting the plugin in debug mode. Have been avoiding Beta 8 until the other plugin compatibility issues are resolved, but if so I will go with it. At this point the plugin is not working.
- Code: Select all
Reloading plugin "Autelis Jandy 1.2.0"
Stopping plugin "Autelis Jandy 1.2.0" (pid 40868)
Stopped plugin "Autelis Jandy 1.2.0"
Starting plugin "Autelis Jandy 1.2.0" (pid 40891)
Started plugin "Autelis Jandy 1.2.0"
****note no connection on port 6000****
May 26, 2013 11:08:03 PM
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Schedule _delayed_action_11
Autelis Jandy Debug TX: #AUX5=0
Autelis Jandy Debug Error: <type 'exceptions.AttributeError'>
Autelis Jandy Error Error in plugin execution ExecuteAction:
Traceback (most recent call last):
File "plugin.py", line 63, in actionAux
File "/Library/Application Support/Perceptive Automation/Indigo 6/Plugins/AutelisJandy.indigoPlugin/Contents/Server Plugin/Autelis.py", line 180, in actionGeneric
File "/Library/Application Support/Perceptive Automation/Indigo 6/Plugins/AutelisJandy.indigoPlugin/Contents/Server Plugin/Autelis.py", line 130, in sendMessage
File "/Library/Application Support/Perceptive Automation/Indigo 6/Plugins/AutelisJandy.indigoPlugin/Contents/Server Plugin/Autelis.py", line 115, in closeConnection
<type 'exceptions.AttributeError'>: 'NoneType' object has no attribute 'close'
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Reloading plugin "Autelis Jandy 1.2.0"
Stopping plugin "Autelis Jandy 1.2.0" (pid 40891)
Autelis Jandy Debug Method: stopConcurrentThread
Autelis Jandy Debug Method: stopConcurrentThread
Stopped plugin "Autelis Jandy 1.2.0"
Starting plugin "Autelis Jandy 1.2.0" (pid 40896)
Started plugin "Autelis Jandy 1.2.0"
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug There was an error reading the plugin preferences. Please check your configuration.
Autelis Jandy Debug Getting Plugin Configuration Settings
doug@dynamic.com wrote:I am working on developing a plug-in for my Niles GXR2 whole home audio system. It is connected via RS-232. I talk to it now with shell scripts to set and obtain data. I notice that your Jandy plug-in uses the same type of serial connection. I was wondering if any of your source code for your plug-in might be available as a basis for my development and communications.
Doug
Reloading plugin "Autelis Jandy 1.2.1"
Stopping plugin "Autelis Jandy 1.2.1" (pid 48709)
Autelis Jandy Debug Method: stopConcurrentThread
Autelis Jandy Debug Method: stopConcurrentThread
Autelis Jandy Debug Method: shutdown
Stopped plugin "Autelis Jandy 1.2.1"
Starting plugin "Autelis Jandy 1.2.1" (pid 48782)
Started plugin "Autelis Jandy 1.2.1"
Autelis Jandy Debug Getting Plugin Configuration Settings
Autelis Jandy Debug Connection Type: Socket
Autelis Jandy Debug Socket IP: 10.0.1.40
Autelis Jandy Debug Socket Port: 6000
Autelis Jandy Debug Enable UDP: False
Autelis Jandy Debug UDP Port: 7890
Autelis Jandy Debug Keypad Updates: True
Autelis Jandy Debug AquaPure: True
Autelis Jandy Debug Aux Devices: 05
Autelis Jandy Debug Aux 01: Aux 1
Autelis Jandy Debug Aux 02: Blower
Autelis Jandy Debug Aux 03: Color Lights
Autelis Jandy Debug Aux 04: Aux 4
Autelis Jandy Debug Aux 05: Control Page Toggle
Autelis Jandy Saved Plugin Configuration
Autelis Jandy Error Socket: 10.0.1.40:6000 not open to close #### don't understand this one.... see below
Autelis Jandy Debug Opening connection....
Autelis Jandy Error Socket: 10.0.1.40:6000 failed to connect. Please check the plugin configuration.
#### Try again...
Autelis Jandy Saved Plugin Configuration
Autelis Jandy Socket: 10.0.1.40:6000 closed succesfully
Autelis Jandy Error Socket: 10.0.1.40:6000 failed to connect. Please check the plugin configuration.
Users browsing this forum: No registered users and 1 guest