Hey Matt,
I'm rather a user than an expert for Z-Wave. So please bear with me if my comments are not sufficient for direct support.
I am using 4 Fibaro FGR-223 for my window shutters and I had them all running in Indigo 7.4. Simply just up/down but that was working for me
With 7.5, I had to resync these devices:
3 FGR-223 sync without (major - just pretty slow and with time outs) problems and I got all the features as described in the manufacturer's manual.
In Indigo 7.4, I got two elements shown for the device (one with all functions and a second one which was unused).
Now, I have 3 elements per device in a device group:
The Energy, of the Device Group has all the settings (as typical for the first device) but i can just update/reset the power consumption.
However, the curren load/total usage shows always 0
The Position and the Slates/Tilt show on/off/brightness/status request functions.
However on all elements, I receive error messages:
Z-Wave Error device "2. Etage - Rolladen - doppel links - Shutter Position" does not support on command
Z-Wave Error device "2. Etage - Rolladen - doppel links - Shutter Position" does not support off command
Z-Wave Error device "2. Etage - Rolladen - doppel links - Shutter Position" does not support status request command
Z-Wave Error device "2. Etage - Rolladen - doppel links - Slats Tilt" does not support off command
Z-Wave Error device "2. Etage - Rolladen - doppel links - Slats Tilt" does not support on command
Z-Wave Error device "2. Etage - Rolladen - doppel links - Slats Tilt" does not support status request command
Consequently, I can operate the roller only manually using the wall switch
The
4th FGR223 refused to finish sync and I receive some encryption error messages:
Z-Wave Syncing - started for "039 - Motor Control Class B"
Z-Wave Syncing - retrieved module neighbors list: 16, 18, 22, 30, 32, 33, 36, 37, 38, 40
Z-Wave Syncing - assigning return route to "039 - Motor Control Class B"
Z-Wave Syncing - assigned return route
Z-Wave Syncing - retrieved manufacture and model names: Fibaro System - 010F, Shutter Controller (FGR223) - 03031000
Z-Wave Error RCVD encryptedPacket: unexpected sequence byte 38
Z-Wave Error RCVD encryptedPacket: full raw packet 01 25 00 04 00 27 1F 98 81 7A B9 D6 01 13 8B 3A F2 C2 84 53 97 1A FF 74 1B 9D 79 13 E4 0F 8F B8 32 6D 5C 4D A5 AA D9
Z-Wave Error RCVD encryptedPacket: encrypted packet C2 84 53 97 1A FF 74 1B 9D 79 13 E4
Z-Wave Error RCVD encryptedPacket: decrypted packet 38 27 07 B5 1B 94 44 23 3A 50 66 D1
Z-Wave Error encrypted command received from node ID 039 has invalid CBC-MAC value (ignoring)
Z-Wave Syncing - retrieved protocol version 6.02, app version 5.01
Z-Wave Error RCVD encryptedPacket: unexpected sequence byte 5D
Z-Wave Error RCVD encryptedPacket: full raw packet 01 1E 00 04 00 27 18 98 81 A4 B4 55 52 ED DD B4 FD 50 BC A3 15 63 F3 14 83 51 4E E1 8D 10 76 E5
Z-Wave Error RCVD encryptedPacket: encrypted packet 50 BC A3 15 63
Z-Wave Error RCVD encryptedPacket: decrypted packet 5D 05 2D B0 D0
Z-Wave Error encrypted command received from node ID 039 has invalid CBC-MAC value (ignoring)
Z-Wave Syncing - retrieved class hierarchy: Routing Slave : Mulitlevel Switch : Motor Control Class B (04 : 11 : 06, base 26)
Z-Wave Syncing - retrieved command classes: 85v1 86v1 8Ev1 98v1 9Fv1 20v1 22v1 25v1 26v1 32v1 55v1 56v1 59v1 5Av1 5Bv1 5Ev1 60v1 6Cv1 70v1 71v1 72v1 73v1 75v1 7Av1
Z-Wave Syncing - retrieved encrypt commands: 85 86 8E 59 5A 5B 60 26 32 70 71 72 73 75 7A
Z-Wave Syncing - retrieved capabilities: routing, beaming, security
Z-Wave Syncing - retrieved battery level of 42%
Z-Wave Error Syncing - failed
Z-Wave Error Timeout waiting for "039 - Motor Control Class B". Module might be asleep, or is unreachable.
Basically, the sync stops almost always at the same position. Sometines with the encryption error messages, sometimes without.
Also, this shutterl I can operate from the wall switch without any problems.
Right next to the FGR223 which isn't synching. I have an FGRM222 for a sunshade. The FRGM222 re-synch at warp speed so I guess it's not a distance/connection problem.
Also, with the FGRM222, I only get one device element (not a device group) which includes all settings, incl. energy.
Any ideas if I make some mistakes here?