Hi
I have some similar problems to that you have in this thread.
I have an Aeon Labs Z-Stick Series 2 (
https://aeotec.freshdesk.com/helpdesk/a ... 6009584533), is that the same as Gen 2 mentioned here?
This summer I changed hardware from a Mac Mini Late 2009 to a Mac Mini 2014.
Before this I never experienced this problem.
After the hardware upgrade, the z-wave network suddenly dies without any explanation.
A reload of the interface solves the problem.
This autumn the problems have got more and more frequent, now almost every week.
Other changes might also be an upgrade to 7.1.1 this summer when I upgraded the hardware.
I tried to upgrade again now last week to 7.2.2
But the problem remains
Here are the last minute of the logfile if it can be any help
2018-12-25 00:04:03.758 Z-Wave received "Cinema - HVAC" mode is heat
2018-12-25 00:04:04.068 Z-Wave received "Cinema - HVAC" fan mode is always on
2018-12-25 00:04:04.378 Z-Wave received "Cinema - HVAC" temperature update to 24 °C
2018-12-25 00:04:04.693 Z-Wave received "Cinema - HVAC" heat setpoint is 18.0 °C
2018-12-25 00:04:05.006 Z-Wave received "Cinema - HVAC" cool setpoint is 23.0 °C
2018-12-25 00:04:07.188 Z-Wave received "073 - Cinema - HVAC" status update battery level 100%
2018-12-25 00:04:09.712 Z-Wave received "Cinema - HVAC" temperature update to 24 °C
2018-12-25 00:05:00.741 Schedule CPV1-Internet Connection Check
2018-12-25 00:05:01.859 Z-Wave sent "Tims Room Floor Heating" on
2018-12-25 00:05:09.760 Z-Wave Error rcvd packet checksum mismatch: 01 00
2018-12-25 00:05:09.760 Z-Wave Error calculated checksum FF, received 00 (sent NAK)
The reason I found this thread is because of error messages after reloadThese devices are removed but still report missing 47,49, 50, 66, 79 how do I remove these?
43, 56 Are disabled by me becase they are broken and needs to be replaced, no need to change anything here.
53 "Kitchen Ceiling Light" and 54 "Master Bedroom Ceiling Light" always reports that they "needs re-sync", but they don't, I just turn on and off them from my Control page and they are normal.
Reloading interface "Z-Wave 2.0.119"
Stopping interface "Z-Wave 2.0.119" (pid 48157)
Z-Wave closed connection to Z-Wave 2.78 static controller
Stopped interface "Z-Wave 2.0.119"
Starting interface "Z-Wave 2.0.119" (pid 57475)
Started interface "Z-Wave 2.0.119"
Z-Wave Error rcvd unexpected bytes (sent ACK): 14 01 00 04 00 62 0E 32 02 21 64 00 00 02 0D 00 03 00 00 02 0D F5
Z-Wave connected to Z-Wave 2.78 static controller interface on /dev/cu.SLAB_USBtoUART (firmware 26.157)
Z-Wave found module included in controller with no matching device (missing or disabled): 001 - Indigo Z-Wave Interface
Z-Wave found module included in controller with no matching device (missing or disabled): 043 - Binary Sensor (routing)
Z-Wave found module included in controller with no matching device (missing or disabled): 047 - Binary Sensor (routing)
Z-Wave found module included in controller with no matching device (missing or disabled): 049 - Relay Power Switch
Z-Wave found module included in controller with no matching device (missing or disabled): 050 - Relay Power Switch
Z-Wave Error device "Kitchen Ceiling Light" should be re-synced using the "Define and Sync..." button in the device edit dialog (the internal device definition has been revised)
Z-Wave Error device "Master Bedroom Ceiling Light" should be re-synced using the "Define and Sync..." button in the device edit dialog (the internal device definition has been revised)
Z-Wave found module included in controller with no matching device (missing or disabled): 056 - Relay Power Switch
Z-Wave found module included in controller with no matching device (missing or disabled): 066 - Binary Sensor (routing)
Z-Wave found module included in controller with no matching device (missing or disabled): 079 - Motor Control Class B
Z-Wave found module included in controller with no matching device (missing or disabled): 093 - Relay Power Switch