Hello everyone,
I've installed two units of this dual relay switch, so we could automate control of 4 different loads (Load 1 / Load 2 in each ZWN-RSM2-PLUS). even though I would like to automate the loads, I also would like to maually control the same loads by using regular switches locally. This unit allows it if you install old school switches locally and connect those to the AUX 1/ AUX 2 terminals of the ZWN-RSM2-PLUS.
Once I paired the units with Indigo, I was immediately able to control the 4 loads, either operating the manual switches locally (i.e. pressing each of the 2 buttons installed locally on either ZWN-RSM2-PLUS), or centrally (i.e using Indigo to send on/off commands to control each load).
The problem I'm facing is: Instant Status reports only seem to report local changes (button presses) for Load1 on both ZWN-RSM2-PLUS units... I have tried to resync, but wasn't able to overcome this issue.
Below is the log contents captured immediately after resyncing and pressing buttons for load 1 and load 2 on one of my ZWN-RSM2-PLUS units. As you can see at the end of the log, only load 1 seem to be reported back to Indigo. The same thing happens oh my other ZWN-RSM2-PLUS unit, so it doesn't seem to be cause by a malfunctioning unit
22 May 2020 12:58:07
Z-Wave Syncing - started for "Hall - Enerwave ZWN-RSM2-PLUS Dual Relay Switch 1"
Z-Wave Syncing - retrieved module neighbors list: 1, 20, 44, 47, 49, 51, 55, 57, 60, 63, 68, 69, 70, 72, 75, 80, 92, 101, 112, 114
Z-Wave Syncing - assigning return route to "113 - Hall - Enerwave ZWN-RSM2-PLUS Dual Relay Switch 1"
Z-Wave Syncing - assigned return route
Z-Wave Syncing - retrieved manufacture and model names: Enerwave - 011A, Relay Power Switch - 01110606
Z-Wave Syncing - retrieved protocol version 4.38, app version 5.12
Z-Wave Syncing - retrieved class hierarchy: Routing Slave : Relay Switch : Relay Power Switch (04 : 10 : 01, base 25)
Z-Wave Syncing - retrieved command classes: 20v1 60v4 25v1 86v1 27v1 8Ev1 72v1 73v1 59v1 5Av1 5Ev1 85v1
Z-Wave Syncing - retrieved encrypt commands: - none -
Z-Wave Syncing - retrieved capabilities: routing, beaming
Z-Wave Syncing - retrieved multi-endpoint types: 1:(10 : 01), 2:(10 : 01)
Z-Wave Syncing - retrieved multi-endpoint classes: 1:[25 20], 2:[25 20]
Z-Wave Syncing - retrieved group 1 associations: [1]
Z-Wave Syncing - retrieved group 2 associations: []
Z-Wave Syncing - retrieved group 3 associations: []
Z-Wave Syncing - group 1 association to interface already exists (skipping)
Z-Wave Syncing - complete
Z-Wave sent "Hall - Enerwave ZWN-RSM2-PLUS Dual Relay Switch 1" status request
Z-Wave sent "Hall - Enerwave ZWN-RSM2-PLUS Dual Relay Switch 2" status request
Z-Wave received "Sensor Varanda - Dry Contact" status update is on
Z-Wave received "Sensor Varanda - Dry Contact" status update is off
22 May 2020 12:58:57
Z-Wave received "Hall - Enerwave ZWN-RSM2-PLUS Dual Relay Switch 1" status update is on
Can anyone please advise how to make Load 2 also report back to Indigo via Instant Status reports?
TIA
Cesar