Fibaro Double Switch Model ID?

Posted on
Thu Nov 08, 2018 3:34 pm
garywiz offline
Posts: 11
Joined: May 11, 2017

Fibaro Double Switch Model ID?

I am having lots of problems with the Fibaro Double Switch. Configuration parameters not available... status updates not reporting for S2. I've seen these in the forums but before I start down the path of diagnosis, I want to be sure I know what model I have. Unfortunately, the electrician has installed the unit inside the wall, and I can't get to it (not without calling him and having him pull the wiring out.... here in Australia, it's illegal to touch wiring yourself). So, I want to be sure I can't solve it without that drastic step.

First, I am seeing a "Model ID" I have not encountered here and can't find online. Here is my status report:

Indigo Z-Wave Version: 2.0.119
Node ID: 10
Model: Relay Power Switch
Model ID: 02023002
Manufacturer: Fibaro System
Manufacturer ID: 010F
Protocol Version: 3.52
Application Version: 2.02
Model Definition Version: 0
Library Type: 3
Class Name: Relay Power Switch
Class Hierarchy: 04 : 10 : 01
Command Class Base: 25
Command Versions: 20v1 60v2 25v1 86v1 27v1 8Ev1 70v1 72v1 73v1 7Av1 85v1
Encryption Status: Not Supported
Multi-Endpoint Types: 1:(10 : 01), 2:(10 : 01)
Multi-Endpoint Classes: 1:[25], 2:[25]
Multi-Instance Counts: - none -
Features: routing, beaming
Neighbors: 9, 11, 12, 13, 14, 15, 16, 17
Associations: 1:[1] 2:[] 3:[]
Config Values: - none -


Note that the model 02023002 is not one I can find anywhere. And, note that "Config Values" indicates "-none-". Any attempt to change any configuration parameter, or query them, fails.

Any advice on where to start?

Posted on
Thu Nov 08, 2018 5:43 pm
matt (support) offline
Site Admin
User avatar
Posts: 21411
Joined: Jan 27, 2003
Location: Texas

Re: Fibaro Double Switch Model ID?

Model ID 02023002 isn't mapped to any Fibaro devices in Indigo yet. Which specific model Fibaro is the one you have so we can get it added?

The Interfaces->Z-Wave->Modify Configuration Parameter... capability should work now though; even without a device definition. Copy/paste the errors you see in the Event Log window after you try to query and set parameter values.

Image

Posted on
Thu Nov 08, 2018 8:14 pm
garywiz offline
Posts: 11
Joined: May 11, 2017

Re: Fibaro Double Switch Model ID?

When I attempt to read config parameter #10 (First channel operating mode), I get the following:

Z-Wave Error failed to read value -- device may not support parameter 10 or may be asleep


I'm pretty sure it's not asleep. :)

The same result comes back for any config parameter listed. I change configuration parameters of Fibaro devices all the time, but they are all RGBW or Dimmer 2 modules. This is the only Double Relay I've used, but it should work the same I would assume.

As far as which exact unit we have, I don't know as it was installed by an electrician. However, I am in the process of getting somebody to help me extract it from the wall so I can find out for sure. If you want to wait until I can actually see the unit and read the sticker to see, that's fine. I won't forget about this thread! I believe it is an FGS-223. That was what was in the electrical spec for the developer.

Note that the unit DOES allow me to control S1 and S2 through Indigo, but does little else. For example, it will not report on switch status. I do receive trigger notifications for S1, but not for S2, nor any energy reports.

Posted on
Fri Nov 23, 2018 10:44 pm
garywiz offline
Posts: 11
Joined: May 11, 2017

Re: Fibaro Double Switch Model ID?

OK, we finally got the unit dug out of the wall (wow, what a project), and I took a photo of the label.

It says "Fibar Group Relay Switch FGS222 AH v2.2"

I am attaching a photo. I hope this helps figure it out!
Attachments
IMG_4130.JPG
IMG_4130.JPG (78.88 KiB) Viewed 1310 times

Posted on
Fri Nov 23, 2018 11:32 pm
matt (support) offline
Site Admin
User avatar
Posts: 21411
Joined: Jan 27, 2003
Location: Texas

Re: Fibaro Double Switch Model ID?

We have a device definition for that model already, so we'll just assign that new model ID (we weren't aware of) to use it as well. That change will be in the next release of Indigo.

Image

Posted on
Fri Nov 23, 2018 11:40 pm
garywiz offline
Posts: 11
Joined: May 11, 2017

Re: Fibaro Double Switch Model ID?

Great, thank you so much. I'll keep an eye out for updates.

Posted on
Fri Feb 01, 2019 6:13 pm
garywiz offline
Posts: 11
Joined: May 11, 2017

Re: Fibaro Double Switch Model ID?

Is there any workaround for this in the meantime? Any "patch" or tweak I can perform to get these units recognised?

Posted on
Mon Feb 04, 2019 4:15 pm
matt (support) offline
Site Admin
User avatar
Posts: 21411
Joined: Jan 27, 2003
Location: Texas

Re: Fibaro Double Switch Model ID?

You can create Trigger Actions to catch the raw Z-Wave commands it sends (to detect button presses). It'll definitely be supported in the next version of Indigo we release. We don't give ETAs but the plan was to have it released quite a while back. :roll:

Image

Posted on
Sun May 12, 2019 4:04 pm
matt (support) offline
Site Admin
User avatar
Posts: 21411
Joined: Jan 27, 2003
Location: Texas

Re: Fibaro Double Switch Model ID?

Indigo 7.3 (and 7.3.1) are now available and include support for new variant of Fibaro Double Relay (FGS222).

Image

Page 1 of 1

Who is online

Users browsing this forum: No registered users and 9 guests