Fibaro relay not reporting device action from switch 2

Hi all,

Just fitted a fibaro relay with 2 channels into a kitchen light switch.

Two switches connected to the relay with 2 outputs to two lighting circuits.

All works fine and is controllable from indigo however when switch 2 is used to turn on the cupboard lights indigo doesn't seem to see the status change of the device.

I've turned on the commands setting so it shows switch 2 pressed but should it show me the end device status as well?

Switch 2 is connected to a separate device called Kitchen Cupboard Lights
Log output below:

Apr 2018, 17:58:00
Schedule TimeIncrement
Z-Wave received "Kitchen Lights" button 2 pressed
Z-Wave received "Kitchen Lights" button 2 pressed
Z-Wave received "Kitchen Lights" status update is off
Z-Wave received "Kitchen Lights" button 1 pressed
Z-Wave received "Kitchen Lights" power load to 0.0 W
Z-Wave received "Kitchen Lights" status update is on
Z-Wave received "Kitchen Lights" button 1 pressed
Z-Wave received "Kitchen Lights" power load to 38.5 W
Z-Wave received "Kitchen Lights" energy total to 0.58 kWh
Z-Wave received "Kitchen Lights" power load to 38.4 W


Thanks
Noel

Do the cupboard lights change/ respond if you tell them to from Indigo?


Sent from my iPhone using Tapatalk Pro

Yes they work fine. Both from Indigo and from the switch.

There was a bug conversation last week about Fibaro Dimmer where Button 2 didn’t get reported to Indigo - but that’s not the case here; it’s reporting and being seen, just not being acted on.

Have you the sync log of when you synced it? I suspect Matt will ask for it shortly. :p


Sent from my iPhone using Tapatalk Pro

Synced as in when I first associated it? No

Just went in and defined and synched and got this:

16 Apr 2018, 18:56:44
Z-Wave Syncing - started for "Kitchen Lights"
Z-Wave Syncing - retrieved module neighbors list: 1, 3, 4, 5, 6, 13, 14, 18, 19, 24, 26
Z-Wave Syncing - assigning return route to "027 - Kitchen Lights"
Z-Wave Syncing - assigned return route
Z-Wave Syncing - retrieved manufacture and model names: Fibaro System - 010F, Double Switch 2 (FGS223) - 02031000
Z-Wave Syncing - retrieved protocol version 4.05, app version 3.02
Z-Wave received "Hall - Motion Sensor - 017 - Motion Sensor" status update is on
Z-Wave Syncing - retrieved class hierarchy: Routing Slave : Relay Switch : Relay Power Switch (04 : 10 : 01, base 25)
Z-Wave Syncing - retrieved command classes: 20v1 60v4 22v1 25v1 86v1 27v1 72v1 8Ev1 70v1 71v1 32v3 73v1 75v1 56v1 98v1 59v1 5Av1 5Bv1 7Av1 5Ev1 85v1
Z-Wave Syncing - retrieved encrypt commands: - none -
Z-Wave Syncing - retrieved capabilities: routing, beaming, security
Z-Wave Syncing - retrieved multi-endpoint types: 1:(10 : 01), 2:(10 : 01)
Z-Wave Syncing - retrieved multi-endpoint classes: 1:[5E 86 25 85 59 8E 32], 2:[5E 86 25 85 59 8E 32]
Z-Wave Syncing - retrieved group 1 associations: [1]
Z-Wave Syncing - retrieved group 2 associations: []
Z-Wave Syncing - retrieved group 3 associations: []
Z-Wave Syncing - retrieved group 4 associations: []
Z-Wave Syncing - retrieved group 5 associations: []
Z-Wave Syncing - group 1 association to interface already exists (skipping)
Z-Wave Syncing - retrieved parameter 20 "Switch type" is 0 "Momentary"
Z-Wave Syncing - retrieved parameter 10 "Switch 1 mode" is 0 "Normal"
Z-Wave Syncing - retrieved parameter 11 "Switch 1 behavior" is 0 "Cancel Delay or Auto Mode"
Z-Wave Syncing - retrieved parameter 28 "Switch 1 scenes" is 15 "Send All"
Z-Wave Syncing - retrieved parameter 12 "Switch 1 duration" is 50 seconds
Z-Wave Syncing - retrieved parameter 13 "Switch 1 flash" is 5 * 100 milliseconds
Z-Wave Syncing - retrieved parameter 50 "Switch 1 power threshold" is 20 %
Z-Wave received "Bathroom - Temperature" sensor update to 22.8 °C
Z-Wave Syncing - retrieved parameter 51 "Switch 1 power delay" is 10 seconds
Z-Wave Syncing - retrieved parameter 53 "Switch 1 energy threshold" is 100 * 0.01 kWh
Z-Wave Syncing - retrieved parameter 15 "Switch 2 mode" is 0 "Normal"
Z-Wave Syncing - retrieved parameter 16 "Switch 2 behavior" is 0 "Cancel Delay or Auto Mode"
Z-Wave Syncing - retrieved parameter 29 "Switch 2 scenes" is 15 "Send All"
Z-Wave Syncing - retrieved parameter 17 "Switch 2 duration" is 50 seconds
Z-Wave Syncing - retrieved parameter 18 "Switch 2 flash" is 5 * 100 milliseconds
Z-Wave Syncing - retrieved parameter 54 "Switch 2 power threshold" is 20 %
Z-Wave Syncing - retrieved parameter 55 "Switch 2 power delay" is 10 seconds
Z-Wave Syncing - retrieved parameter 57 "Switch 2 energy threshold" is 100 * 0.01 kWh
Z-Wave Syncing - retrieved parameter 58 "Periodic power reports" is 3600 seconds
Z-Wave Syncing - retrieved parameter 59 "Periodic energy reports" is 3600 seconds
Z-Wave Syncing - retrieved parameter 9 "Power up to last known state" is true
Z-Wave Syncing - complete
Z-Wave sent "Kitchen Lights" status request
Z-Wave sent "Kitchen Lights" energy status request
Z-Wave sent "Kitchen Cupboard Lights" status request
Z-Wave sent "Kitchen Cupboard Lights" energy status request

Looks healthy to me, but Matt is better at sync/device issues.

I deal more with raw Zwave queries - but we know your command is being seen.

Erm, what is polling set to on this device?


Sent from my iPhone using Tapatalk Pro

Enabled
Only when activity detectwd

Try this thread - http://forums.indigodomo.com/viewtopic.php?f=58&t=18165 - it may help as I think it solved a similar issue for me in the past.

Try this thread - http://forums.indigodomo.com/viewtopic.php?f=58&t=18165 - it may help as I think it solved a similar issue for me in the past.

Awesome thanks Colly, yes that's fixed it although I don't know scene commands in the logs. I've posted in the other thread about that.

Thanks guys, incredibly responsive of all of you!!!

Cheers
Noel