Devolo Thermostat Room Sensor (Link RS)

Posted on
Mon Nov 09, 2020 12:52 pm
Bildhauer offline
Posts: 160
Joined: Sep 30, 2019
Location: 22113 Oststeinbek (near Hamburg), Germany

Devolo Thermostat Room Sensor (Link RS)

Hello all,

home can I manage it that the heatpoint of a Devolo Thermostat Room Sensor (Link RS) "Devolo Thermostat Buero" will be the heatpoint of a Radiator Thermostat (Devolo 09356) "Devolo Heizungsthermostat Buero"?. At the moment my settings are as attached.

Best regards

Bildhauer

Posted on
Mon Nov 09, 2020 2:38 pm
autolog offline
Posts: 3988
Joined: Sep 10, 2013
Location: West Sussex, UK [GMT aka UTC]

Re: Devolo Thermostat Room Sensor (Link RS)

No settings attached to previous post. :wink:

Have you read the documentation here: TRV Controller Documentation :?:

Post back if you need more guidance. :)

Posted on
Tue Nov 10, 2020 9:58 am
Bildhauer offline
Posts: 160
Joined: Sep 30, 2019
Location: 22113 Oststeinbek (near Hamburg), Germany

Re: Devolo Thermostat Room Sensor (Link RS)

Yes I did it the way described.

Attached my screenshot.
Attachments
Configure_TRV_Controller.jpg
Configure_TRV_Controller.jpg (357 KiB) Viewed 2237 times

Posted on
Tue Nov 10, 2020 10:12 am
autolog offline
Posts: 3988
Joined: Sep 10, 2013
Location: West Sussex, UK [GMT aka UTC]

Re: Devolo Thermostat Room Sensor (Link RS)

You should set your Devolo Thermostat Buero up as a remote thermostat not as the heating source.

A heating source is typically a hot water boiler providing hot water to the radiator with the TRV. When the TRV or associated remote setpoint is set to a greater value than the TRV or remote measured temperature, the TRV will call for heat i.e. please supply me with hot water.

You need to read the section Remote Details and enable TRV Remote Control.

Hopefully that will get you sorted, if not please post back here. :)

Posted on
Wed Nov 11, 2020 6:42 am
Bildhauer offline
Posts: 160
Joined: Sep 30, 2019
Location: 22113 Oststeinbek (near Hamburg), Germany

Re: Devolo Thermostat Room Sensor (Link RS)

Doing it that way I am getting the error message as shown in my attached screen shot.

Best regards

Bildhauer
Attachments
Configure_TRV_Controller_und_Create_New_Device_und_Grenzweg.jpg
Configure_TRV_Controller_und_Create_New_Device_und_Grenzweg.jpg (133.49 KiB) Viewed 2202 times

Posted on
Wed Nov 11, 2020 7:20 am
autolog offline
Posts: 3988
Joined: Sep 10, 2013
Location: West Sussex, UK [GMT aka UTC]

Re: Devolo Thermostat Room Sensor (Link RS)

You still haven't set it up correctly according to the instructions AFAICS. :wink:

Your TRV should be the Devolo 09356 which is supported by the TRV plugin.

Your remote thermostat should be the Devolo Thermostat Room Sensor (Link RS).

The error message is saying that you have specified the Devolo Thermostat Room Sensor (Link RS) as the TRV, not the Devolo 09356.

Make the changes and then post back how you are getting on. :)

Page 1 of 1

Who is online

Users browsing this forum: No registered users and 1 guest