recurring error, unifi access??

Could you switch off controller info in config?

I need to look I to it a little deeper to tomorrow


Sent from my iPhone using Tapatalk

sorry what do you mean 'switch off controller info in config'?

i did restart the controller a couple times to see if that helps, but so far no.

thanks!

In the plugin config you can select to use the controller info at different levels
Select off


Sent from my iPhone using Tapatalk

i turned controller type to = 'off'

if that's what you mean.

i tried to change controller info to 'off' but it auto-selects 'ON' each time i press enter.

What is your setup? Ie controller type?


Sent from my iPhone using Tapatalk

in version .387 you can set timeout to any value.

please try w time = 25 secs.

in plugin/config/general section at bottom
(make sure that you use a number, no spaces or letters)

Karl

.. and you can set controller to "off" then the controller will be ignored.

AP and switches still work ie who do phone join/leave wifi

thx Karl.

with new version i cannot make a controller type stick, it reverts to off/blank upon config save.

so, i can't actually test this version.

i have set t/o to 25s, but doesn't matter as it won't take a controller config setting.

i have a hosted controller btw.

also, i find the info on device state to be quite unreliable without a controller in the system. so, i do need a controller interface here.


thx a lot for keeping on this!

Make sure that userid passwd ip port is set also.


Sent from my iPhone using Tapatalk

when you change controller type it also changes some defaults, but may be not if you reverse the settings (ie from hosted to off and back to hosted)
I tried to automate any switch of type, but there are some many options and versions that it is difficult to get this right in all directions.

Karl

this is what i get now.

also, the ssh pswrd seems to have unpopulated as well. far as i know that was autofill. i never assigned one. just intended to use controller.


thx

Code: Select all

  Started plugin "uniFiAP 2022.42.387"
   uniFiAP                         debug settings :[]
   uniFiAP Error                   UNIFI executeCMDOnController  login url:https://192.168.100.100:8443/api/login
gives, ok not found or status_code:400 not in [200]
  error: {"meta":{"rc":"error","msg":"api.err.Invalid"},"data":[]}

   uniFiAP Error                   UNIFI executeCMDOnController  login url:https://192.168.100.100:8443/api/login
gives, ok not found or status_code:400 not in [200]
  error: {"meta":{"rc":"error","msg":"api.err.Invalid"},"data":[]}

   uniFiAP                         initialized ... looping
   uniFiAP Error                   UNIFI executeCMDOnController  login url:https://192.168.100.100:8443/api/login
gives, ok not found or status_code:400 not in [200]
  error: {"meta":{"rc":"error","msg":"api.err.Invalid"},"data":[]}

   uniFiAP Error                   UNIFI executeCMDOnController  login url:https://192.168.100.100:8443/api/login
gives, ok not found or status_code:400 not in [200]
  error: {"meta":{"rc":"error","msg":"api.err.Invalid"},"data":[]}


Jul 19, 2023 at 8:14:24 AM
   uniFiAP Error                   getMessages: (1 - test connect)  error for APtail, ip#: 192.168.100.10, prompt:'8# '; wrong ip/ password or system down or ssh timed out or ..?
   uniFiAP Error                   getMessages: (1 - test connect)  error for APdict, ip#: 192.168.100.10, prompt:'8# '; wrong ip/ password or system down or ssh timed out or ..?
   uniFiAP Error                   getMessages: (1 - test connect)  error for APtail, ip#: 192.168.100.11, prompt:'8# '; wrong ip/ password or system down or ssh timed out or ..?
   uniFiAP Error                   getMessages: (1 - test connect)  error for APdict, ip#: 192.168.100.11, prompt:'8# '; wrong ip/ password or system down or ssh timed out or ..?
   uniFiAP Error                   getMessages: (1 - test connect)  error for SWdict, ip#: 192.168.100.21, prompt:'2# '; wrong ip/ password or system down or ssh timed out or ..?
   Schedule                        garage door telltale sync
   uniFiAP Error                   getMessages: (1 - test connect)  error for SWdict, ip#: 192.168.100.20, prompt:'2# '; wrong ip/ password or system down or ssh timed out or ..?
   uniFiAP Error                   getMessages: (1 - test connect)  error for SWdict, ip#: 192.168.100.21, prompt:'2# '; wrong ip/ password or system down or ssh timed out or ..?
   uniFiAP Error                   getMessages: (1 - test connect)  error for SWdict, ip#: 192.168.0.5, prompt:'2# '; wrong ip/ password or system down or ssh timed out or ..?
   uniFiAP                         debug settings :[]
   uniFiAP Warning                 restart  GW ipNumber   changed;
   uniFiAP                         after loop , quitNow= >>config changed<<
   uniFiAP                          resetDataStats called from postLoop
   uniFiAP Warning                 comsumeDictData: stopping process due to stop request
   uniFiAP Warning                 comsumeLogData: stopping process due to stop request
   uniFiAP Warning                 getMessages: stopping listener process for :APdict - 192.168.100.11
   uniFiAP Error                   getMessages: (1 - test connect)  error for APtail, ip#: 192.168.100.10, prompt:'8# '; wrong ip/ password or system down or ssh timed out or ..?
   uniFiAP Error                   getMessages: (1 - test connect)  error for SWdict, ip#: 192.168.0.6, prompt:'2# '; wrong ip/ password or system down or ssh timed out or ..?
   uniFiAP Error                   getMessages: (1 - test connect)  error for

your user id / pwds must be wrong, remember there are several

ssh to devices
http to controller

and could you switch on debug (6), (6.1) (7) (14)

thx Karl

the pw to controller is correct, i have checked it several times manually

the pw to the devices via ssh, as i said, i never entered, never knew it, seems that it auto-populated at some point but now has disappeared. is this possible? does that autofill at any point?

thanks!

you can check if ssh is enabled on the controller (login to the controller) then / settings / system/ then depending on your version.. mine is under advanced

ok, will look soon as i get a sec. thx!