[ANSWERED] MIMOlite device appears as 4 different devices

Trying to map programming to output relay in MIMOLite - the MIMOlite module shows up as 4 different devices and I cannot attach any actions to any of them. Is it possible I have a defective unit? Just trying to do simple on/off action to relay upon z wave command.

[matt (support)]

Hello,

You may have a MIMOLite with a different model ID than what we've encountered. If that is the case, then we just need to get it added and it will work better. Try doing the sync operation again (from the Device dialog), then copy/paste the results from the Event Log window into a reply for me.

Here you go! Thanks tons and I have my fingers crossed!
May 28, 2014 8:34:23 PM
Z-Wave Syncing - started for device "006 - Binary Input"
Z-Wave Syncing - retrieved module neighbors list: - none -
Z-Wave Syncing - requesting neighbor list update of "006 - Binary Input"
Z-Wave Syncing - neighbor list update failed -- will try to update nearby neighbors first
Z-Wave Syncing - requesting neighbor list update of "006 - Binary Input"
Z-Wave Error Syncing - neighbor list update failed
Z-Wave Syncing - assigning return route to "006 - Binary Input"
Z-Wave Syncing - assigned return route
Z-Wave Syncing - retrieved manufacture and model names: FortrezZ - 0084, I/O Module (MIMOlite) - 0453010F
Z-Wave Syncing - retrieved protocol version 3.42, app version 1.15
Z-Wave Syncing - retrieved class hierarchy: Routing Slave : Relay Switch : -- (04 : 10 : 00, base 25)
Z-Wave Syncing - retrieved command classes: 20v1 00v1 71v1 25v1 86v1 30v1 70v1 31v1 72v1 35v1 85v1
Z-Wave Syncing - retrieved group 1 associations: [5]
Z-Wave Syncing - retrieved group 2 associations: [1]
Z-Wave Syncing - retrieved group 3 associations: [1]
Z-Wave Syncing - retrieved group 4 associations: [1]
Z-Wave Syncing - retrieved group 5 associations: [1]
Z-Wave Syncing - group 2 association to interface already exists (skipping)
Z-Wave Syncing - group 3 association to interface already exists (skipping)
Z-Wave Syncing - group 4 association to interface already exists (skipping)
Z-Wave Syncing - group 5 association to interface already exists (skipping)
Z-Wave Syncing - retrieved Input sensor changes output relay is false
Z-Wave Syncing - retrieved parameter 9 "Delay between reporting analog input and pulse count (0: disabled)" is 0 * 10 seconds
Z-Wave Syncing - retrieved parameter 11 "Delay before relay automatically toggles OFF (0: disabled)" is 255 * 100 milliseconds
Z-Wave Syncing - retrieved parameter 8 "Input flags (3: use digital thresholds, 1: use custom thresholds)" is 3
Z-Wave Syncing - retrieved OFF binary input HIGH threshold is 187
Z-Wave Syncing - retrieved OFF binary input LOW threshold is 171
Z-Wave Syncing - retrieved ON binary input HIGH threshold is 255
Z-Wave Syncing - retrieved ON binary input LOW threshold is 254
Z-Wave Syncing - complete
Z-Wave sent "006 - Binary Input" status request
Z-Wave sent "006 - Analog Input" status request
Z-Wave sent "006 - Pulse Count" status request
Z-Wave sent "006 - Relay Output" status request
Z-Wave received "006 - Binary Input" status update is on
Z-Wave received "006 - Analog Input" sensor update to 2152
Z-Wave received "006 - Pulse Count" sensor update to 2

[matt (support)]

That all looks good to me.

The device that controls the relay is the 4th one in the device dialog. It looks like it has the device name:

006 - Relay Output

The problem might be the Action type you are choosing. Try using the Type: Device Actions -> Light / Appliance Controls -> Turn On/Off. You should also be able to select that device in the main window and use the Turn On and Turn Off buttons at the bottom of the window to manually control the relay from Indigo.