Aeotec zw100 Mutli Sensor 6

I just added one of these bad boys to Indigo.

I managed to add it to the zwave network. It will report tamper, but not any other variable (temp, lum, etc.)

Do I need to do something else?

I've resynched it, still no display in the main indigo window for temp/lum/hum/etc.

Here's the log dump for the synch:


Z-Wave Syncing - started for "Multi 6 044 - Motion Sensor"
Z-Wave Syncing - retrieved module neighbors list: 6, 34, 36, 38
Z-Wave Syncing - assigning return route to "Multi 6 044 - Motion Sensor"
Z-Wave Syncing - assigned return route
Z-Wave received "Christmas tree 006 - Smart Plug (HKZW-SO01)" power load to 42.194 W
Z-Wave Syncing - retrieved manufacture and model names: Aeon Labs - 0086, Multi Sensor 6 (ZW100) - 01020064
Z-Wave received "Indoor Christmas lights036 - Smart Plug (HKZW-SO01)" power load to 2.365 W
Z-Wave Syncing - retrieved protocol version 4.54, app version 1.12
Z-Wave Syncing - retrieved class hierarchy: Routing Slave : Multilevel Sensor : Multilevel Sensor (routing) (04 : 21 : 01, base 31)
Z-Wave Syncing - retrieved command classes: 20v1 80v1 84v2 85v1 86v1 30v1 70v1 71v1 72v1 73v1 5Av1 59v1 31v5 7Av1 5Ev1
Z-Wave Syncing - retrieved encrypt commands: - none -
Z-Wave Syncing - retrieved capabilities: routing, battery, beaming, waking
Z-Wave Syncing - retrieved wake interval of 60 minutes
Z-Wave Syncing - device "Multi 6 044 - Motion Sensor" wake interval changed to 60 minutes
Z-Wave received "044 - Tamper" status update is on
Z-Wave Syncing - retrieved group 1 associations: [1]
Z-Wave Syncing - group 1 association to interface already exists (skipping)
Z-Wave Syncing - retrieved parameter 252 "Lock configuration" is false
Z-Wave Syncing - retrieved parameter 2 "Wake for 10 minutes after battery change" is false
Z-Wave Syncing - retrieved parameter 4 "Motion sensing" is 5 "Sensitivity 5 - Maximum"
Z-Wave received "044 - Tamper" status update is on
Z-Wave Syncing - retrieved parameter 3 "Off delay" is 240 seconds
Z-Wave Syncing - retrieved parameter 5 "Motion flags" is 1
Z-Wave Syncing - retrieved parameter 40 "Enable selective threshold reporting" is false
Z-Wave Syncing - retrieved parameter 64 "Temperature units" is 2 "Fahrenheit"
Z-Wave Syncing - retrieved parameter 111 "Reporting interval" is 1800 seconds
Z-Wave Syncing - device "Multi 6 044 - Motion Sensor" parameter 111 "Reporting interval" changed to 300 seconds (was 1800 seconds)
Z-Wave Syncing - retrieved parameter 112 "Reporting interval2" is 1800 seconds
Z-Wave Syncing - retrieved parameter 113 "Reporting interval3" is 1800 seconds
Z-Wave Syncing - retrieved parameter 101 "Group 1 flags" is 240
Z-Wave Syncing - retrieved parameter 102 "Group 2 flags" is 0
Z-Wave Syncing - retrieved parameter 103 "Group 3 flags" is 0
Z-Wave Syncing - retrieved battery level of 50%
Z-Wave Syncing - complete

update, it looks like only tamper is working:

Z-Wave received "044 - Tamper" status update is on
Z-Wave received "044 - Tamper" status update is on

Anything I need to do to enable the other sensors?

[matt (support)]

Still no updates for motion, temperature, etc.?

Have you tried decreasing the Off Delay setting for it down from the default of 240 seconds to 20 seconds or so? You can also change the reporting interval for the temperature (I think currently it is 300 seconds).

You might also want to try excluding, re-including, and re-syncing it on the possibility it is in a bad state.