Fibaro Door / Window ZW+ sensor FGK-10x

Matt,

1st option

Any update on this as I also am getting no change when the magnet makes/breaks, looking at the debug it shows "Z-Wave received "021 - Tamper Switch" status update is off" for both the magnet make/break and also the external button close/open. Pressing the tamper shows no update.
This is on Fibaro Door/Window Sensor (FGK10x), firmware 3.02

[matt (support)]

Update coming soon...

[matt (support)]

Indigo 7.0.2 is now available for download and should now detect the sensor changes.

Updated to 7.0.2 and the magnet works 100%, the external switch 100% but the tamper switch fails to change in the GUI, the log file is

4 Nov 2016 11:03:01
Z-Wave Debug RCVD nonceFetch: node 021
Z-Wave Debug SENT nonceReport: 01 11 00 13 15 0A 98 80 32 1B 7D DA 63 AA A9 8D 25 67 DB
Z-Wave Debug RCVD encryptedPacket: 00 71 05 00 00 00 FF 07 00 00 (decrypted)
Z-Wave Debug RCVD requestAlarmSensorStatus: 01 0F 00 04 00 15 09 71 05 00 00 00 FF 07 00 00 FF
Z-Wave Debug . . requestAlarmSensorStatus: node 021, endpoint None, cmdClass 71, type 0, value 0, classSubKey 710000
Z-Wave Debug . . requestAlarmSensorStatus: typeExt 7, valueExt 0, classSubKeyExt 7100000700
Z-Wave Debug . . requestAlarmSensorStatus: defnStatusByte 0
Z-Wave received "021 - Tamper Switch" status update is off
Z-Wave Debug RCVD nonceFetch: node 021
Z-Wave Debug SENT nonceReport: 01 11 00 13 15 0A 98 80 11 9D 21 24 DE 10 46 BA 25 68 0C
Z-Wave Debug RCVD encryptedPacket: 00 71 05 00 00 00 FF 07 03 00 (decrypted)
Z-Wave Debug RCVD requestAlarmSensorStatus: 01 0F 00 04 00 15 09 71 05 00 00 00 FF 07 03 00 FF
Z-Wave Debug . . requestAlarmSensorStatus: node 021, endpoint None, cmdClass 71, type 0, value 0, classSubKey 710000
Z-Wave Debug . . requestAlarmSensorStatus: typeExt 7, valueExt 3, classSubKeyExt 7100000703
Z-Wave Debug . . requestAlarmSensorStatus: defnStatusByte 255
Z-Wave received "021 - Tamper Switch" status update is on

CliveS

[matt (support)]

Hi Clive,

Are you positive the GUI isn't updating? These two Event Log lines indicate that Indigo is catching the commands and updating the UI:

Code: Select all

Z-Wave received "021 - Tamper Switch" status update is off
...
Z-Wave received "021 - Tamper Switch" status update is on

I have the unit operating with a remote switch. The tamper button did report correctly in the UI once, but I see nothing in the log when retesting and no change in the UI. I'll look into it further tomorrow.

The only thing I can report for sure is that the auto off on the tamper did not occure after 5 seconds.

Door/Window Sensor (FGK10x), firmware 3.02

Works great as a door bell, and sends imessage with a camera shot too

Matt,
My mistake (or more my impatience), I was not waiting 5 seconds before the tamper was set to off, I just was pressing the tamper on then off, obviously if it is fixed on a wall then 5 seconds is irrelevant as it should stay like that until someone pulls it off or have to change the battery. I think I also confused myself (not difficult!) by running 7.0.2 on the server but not updating the Mac used to remote to it as that was still on 7.0.1

So yes it is working 100% as well as the magnet and external switch....
My thanks to both of you for Indigo 7.

CliveS

I have the Fibaro FGK10x door/window sensor. Do I understand that I should be able to now see a temperature reading (in addition to tamper and open/close ) with version 7.0.2. I tried syncing the device but still only see two devices listed (tamper and open/close). I see the temperature sensitivity setting when I edit device settings.

I have Fibaro motion sensors and leak detector and I get the temperature reading with these but not with the door/window sensor.

Please advise.

My understanding is that you need to connect a temp module to the door sensor
http://www.vesternet.com/ds18b20-programmable-resolution-1-wire-digital-thermometer

I have the Fibaro FGK10x door/window sensor. Do I understand that I should be able to now see a temperature reading (in addition to tamper and open/close ) with version 7.0.2. I tried syncing the device but still only see two devices listed (tamper and open/close). I see the temperature sensitivity setting when I edit device settings.

I have Fibaro motion sensors and leak detector and I get the temperature reading with these but not with the door/window sensor.

Please advise.

Thanks. Missed where is said the Fibaro Door/Window sensor SUPPORTS a temperature sensor.

Any recommendations on the simplest (and cheap and small) temperature only sensor. These BS18B20 sensors are very cheap but I need to connect it to something supported by Indigo (Zwave). I have a few needs for monitoring temperature only. Adding a sensor to a door sensor or using a motion sensor to measure temperature only seems like a waste.

Thanks much,

Jim

Just a related question: does the sensor blink always when the door opens or closes or only if it is able to communicate to the Z-Wave stick?

hi,

I just get no temp-reading. to clarify: I get the parameters for temperature in the setting dialog - bit nowhere a temp-reading. I checked the connection to the ds18b20 several time also the wiring... maybe it is broken? how to find out? also tried with another fkg10x same result...

thx for help!

l