- Posted on
Tue May 18, 2021 7:41 am
-
durosity
offline
-
- Posts: 4354
- Joined: May 10, 2012
- Location: Newcastle Upon Tyne, Ye Ol' England.
Hmm I will have a look see if there's a way to manually reset it - I'd have thought excluding and inclusion would have that effect but ¯\_(ツ)_/¯
Here's the device dump in case it's of use:
Indigo Z-Wave Version: 7.5.0
Node ID: 130
Model: Shutter Controller (FGR223)
Model ID: 03031000
Manufacturer: Fibaro System
Manufacturer ID: 010F
Protocol Version: 6.02
Application Version: 5.01
Model Definition Version: 1
Library Type: 3
Class Name: Motor Control Class B
Class Hierarchy: 04 : 11 : 06
Command Class Base: 26
Command Versions: 20v1 85v1 86v1 8Ev1 55v1 56v1 98v1 59v1 5Av1 5Bv1 5Ev1 9Fv1 60v4 22v1 25v1 26v4 6Cv1 32v3 70v1 71v1 72v1 73v1 75v1 7Av1
Encryption Status: Supported but not Enabled
Multi-Endpoint Types: 1:(11 : 06), 2:(11 : 06)
Multi-Endpoint Classes: 1:[5E 26 85 8E 59 98 9F 6C 32 71 22], 2:[5E 26 85 8E 59 98 9F 6C 22]
Multi-Instance Counts: - none -
Features: routing, beaming, security, energyMeter
Neighbors: 5, 6, 7, 10, 11, 12, 15, 16, 17, 18, 27, 28, 29, 31, 32, 33, 35, 50, 51, 61, 78, 82, 84, 87, 88, 90, 95, 99, 100, 101, 102, 104, 107, 115, 122, 125, 128, 129
Associations: 1:[1] 2:[] 3:[]
Config Values: 152:0 20:0 150:0 151:1 24:0 25:0 154:10 155:10 156:1000 157:1000 40:0 41:0 60:1 61:15 62:3600 65:10 66:3600 153:0
As for the resync:
Z-Wave Syncing - retrieved module neighbors list: 5, 6, 7, 10, 11, 12, 15, 16, 17, 18, 27, 28, 29, 31, 32, 33, 35, 50, 51, 61, 78, 82, 84, 87, 88, 90, 95, 99, 100, 101, 102, 104, 107, 115, 122, 125, 128, 129
Z-Wave Syncing - assigning return route to "130 - ZZ - Unused 130a"
Z-Wave Syncing - assigned return route
Z-Wave Syncing - retrieved manufacture and model names: Fibaro System - 010F, Shutter Controller (FGR223) - 03031000
Z-Wave Syncing - retrieved protocol version 6.02, app version 5.01
Z-Wave Syncing - retrieved class hierarchy: Routing Slave : Mulitlevel Switch : Motor Control Class B (04 : 11 : 06, base 26)
Z-Wave Syncing - retrieved command classes: 85v1 86v1 8Ev1 98v1 9Fv1 20v1 22v1 25v1 26v4 32v3 55v1 56v1 59v1 5Av1 5Bv1 5Ev1 60v4 6Cv1 70v1 71v1 72v1 73v1 75v1 7Av1
Z-Wave Syncing - retrieved encrypt commands: - none -
Z-Wave Syncing - retrieved capabilities: routing, beaming, security
Z-Wave Syncing - retrieved multi-endpoint types: 1:(11 : 06), 2:(11 : 06)
Z-Wave Syncing - retrieved multi-endpoint classes: 1:[5E 26 85 8E 59 98 9F 6C 32 71 22], 2:[5E 26 85 8E 59 98 9F 6C 22]
Z-Wave Syncing - retrieved group 1 associations: []
Z-Wave Syncing - retrieved group 2 associations: []
Z-Wave Syncing - retrieved group 3 associations: []
Z-Wave Syncing - added group 1 multi association to interface
Z-Wave Syncing - retrieved parameter 151 "Operating mode" is 1 "Roller with Position"
Z-Wave Syncing - retrieved parameter 150 "Force calibration" is 1 "Calibrated"
Z-Wave Syncing - device "130 - ZZ - Unused 130a" parameter 150 "Force calibration" changed to 0 "Not Calibrated" (was 1 "Calibrated")
Z-Wave Syncing - retrieved parameter 156 "Up movement duration" is 1000 * 10 milliseconds
Z-Wave Syncing - retrieved parameter 157 "Down movement duration" is 1000 * 10 milliseconds
Z-Wave Syncing - retrieved parameter 152 "Slats duration and gate close timer" is 150 * 10 milliseconds
Z-Wave Syncing - device "130 - ZZ - Unused 130a" parameter 152 "Slats duration and gate close timer" changed to 0 * 10 milliseconds (was 150 * 10 milliseconds)
Z-Wave Syncing - retrieved parameter 153 "Slats position return to previous" is 0 "Only When Indigo Controlled"
Z-Wave Syncing - retrieved parameter 154 "Motor stop delay after end switch" is 10 * 100 milliseconds
Z-Wave Syncing - retrieved parameter 155 "Motor operation detection" is 10 watts
Z-Wave Syncing - retrieved parameter 20 "Switch type" is 0 "Momentary"
Z-Wave Syncing - retrieved parameter 40 "Switch 1 scenes" is 0 "Disabled"
Z-Wave Syncing - retrieved parameter 41 "Switch 2 scenes" is 0 "Disabled"
Z-Wave Syncing - retrieved parameter 24 "Reverse S1 and S2 input operation" is false
Z-Wave Syncing - retrieved parameter 25 "Reverse Q1 and Q2 output operation" is false
Z-Wave Syncing - retrieved parameter 61 "Power report threshold" is 15 %
Z-Wave Syncing - retrieved parameter 62 "Periodic power reports" is 3600 seconds
Z-Wave Syncing - retrieved parameter 60 "Include internal usage in power reports" is true
Z-Wave Syncing - retrieved parameter 65 "Energy report threshold" is 10 * 0.01 kWh
Z-Wave Syncing - retrieved parameter 66 "Periodic energy reports" is 3600 seconds
Z-Wave Syncing - complete
Z-Wave sent "Mike's Study - Window Opener" status request
Z-Wave sent "Mike's Study - Window Opener" energy status request
Z-Wave sent "ZZ - Unused 130b" status request
Z-Wave received "ZZ - Unused 130b" status update brightness 100
Z-Wave received "050 - Temperature 1" sensor update to 1
And changing a parameter, in this case the "Up movement duration":
Z-Wave device "130 - ZZ - Unused 130a" parameter 156 "Up movement duration" changed to 100 * 10 milliseconds
And setting 'force calibration: force calibration now' (which outwardly doesn't seem to do anything:
Z-Wave device "130 - ZZ - Unused 130a" parameter 150 "Force calibration" changed to 2 "Force Calibration Now"
Computer says no.